- Out-of-Stock
These premium wires are stranded 22AWG wires with female terminals on one end and male terminals on the other end. Together with our 0.1" crimp connector housings, these wires can be used to make custom cables with 0.1" (2.54mm) connectors. The assortment of 36" (90 cm) wires includes two each of ten different colors.
![]() |
| 0.1" connector custom cable. |
|---|
These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1×1 crimp connector housings on the ends. By combining these wires with our crimp connector housings, you can quickly and easily create custom cables with 0.1" (2.54mm) connectors that mate with various 0.1"-spaced connectors, including male and female headers and solderless breadboards. Just pick the housing for the correct number of pins, pick the colors and genders for your wires, and snap them into the housings (note: it’s not easy to get the wires back out, so plan carefully!). No soldering is required!
You can easily make cable harnesses or assemblies that branch from one connector on one side to multiple connectors on the other (an example of this is shown in the picture to the right); you can also cut off one pre-crimped end and solder the wires directly to components to make swapping connections easy, as shown in the motor picture below.
The wires are available in six lengths—3" (7.5 cm), 6" (15 cm), 12" (30 cm), 24" (60 cm), 36" (90 cm), and 60" (150 cm)—and in ten colors:
![]() |
| 0.1" connector custom motor cable. |
|---|
These are the same colors as those used on resistor color codes and rainbow ribbon cable. The wire packs of different lengths include different quantities of wires. The table below shows the quantity included for a particular length-color combination:
| length | monochromatic pack quantity | rainbow pack quantity |
|---|---|---|
| 3" | – | 50 (5 of each color) |
| 6" | 10 | 50 (5 of each color) |
| 12" | 10 | 50 (5 of each color) |
| 24" | 5 | 50 (5 of each color) |
| 36" | 5 | 20 (2 of each color) |
| 60" | 2 | 10 (1 of each color) |
These wires can be purchased with male terminals on both ends, female terminals on both ends, or one male and one female terminals. These crimped terminals are designed for use with 0.1" (2.54 mm) male headers and female headers, solderless breadboards, and prototyping PCBs. Note that we also sell the crimp pins by themselves if you want to crimp your own wires.
![]() |
![]() |
| Female crimp pin for 0.1" housings crimped onto a wire. |
|---|
![]() |
| Male crimp pin for 0.1" housings crimped onto a wire. |
|---|
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x3-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x1-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x2-Pin 25-Pack |
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Infrared sensor that allows measurement of distances up to 15cm, has a built-in infrared illuminator, IR receiver and a perimeter of the received signal
No product available!
Miniature (22x13.5x6mm) WiFi module b / g / n with TCP and UDP protocols operating in standalone and access point modes. 2.0mm goldpin connector. The module is equipped with a UART interface, it is also possible to control GPIO lines (also as PWM). Powered by 3.3V. Antenna: copper wire
No product available!
Ultra miniature WiFi b/g/n module, equipped with UART, SPI, PWM and GPIO interfaces. The ability to work as an access point and in standalone mode. 3.3V power supply.HF-LPT200-1
No product available!
This transducer is about 45mm in diameter and has 4Ω impedance and should be run at about 5W
No product available!
No product available!
Read/Write analog front end for 125 kHz RFID Basestation, SOIC16, EM Microrlectronic, RoHS
No product available!
Bitscope Micro is a miniature measuring instrument with a USB interface, it can act as an 8-channel logic analyzer (40MS / s, 3.3V or 5V) or a 2-channel oscilloscope (bandwidth up to 20MHz). In addition, Bitscope can generate a clock signal as well as sinusoidal, triangular, rectangular and saws
No product available!
High performance WLAN USB module which enables the Raspberry Pi to connect to a Wi-Fi network
No product available!
Kit for building a minisumo robot on a crawler chassis. It has a bulldozer, control board and a set of caterpillars. Robot version for self-assembly, requires additional motors and four AA batteries. Pololu 3124
No product available!
Expansion module kit with Arduino compatible connectors for building a Zumo robot. The module includes a dual engine controller, buzzer and user button, as well as a 3-axis accelerometer and compass. Pololu 2508
No product available!
Bi-directional converter enabling communication of any device equipped with an RS232 serial port with 802.11 b / g / n wireless WiFi network. The module can work as a TCP client / TCP or UDP server. The layout is "transparent" for communicating systems, which does not doubt facilitate communication between them.
No product available!
USB A-microB USB cable with a length of 1m, white-blue cable, flat, green plugs illuminated with RGB diode
No product available!
1m USB A-microB USB cable, white-blue cable, flat pink RGB LED illuminated plugs
No product available!
The module is used to build prototypes and designs based on the popular ATmega8 microcontroller. It is possible to mount another microcontroller from the AVR family, if only pin outs coincide with ATmega8. MOD-01.Z
No product available!
No product available!
Module with a relay with a permissible maximum current of 10A with a 5V coil (MOD-03.Z). The module has a transistor relay control transistor and an overvoltage / self-inductive diode from the coil.
No product available!