- Out-of-Stock
This is a rechargeable 4.8 V NiMH battery pack with a capacity of 200 mAh. The pack consists of four 1/3-size AAA cells in a single row and a 4" lead terminated by a “JR”-style connector.
![]() |
This battery pack comes with 4" leads terminated by a 3-pin JR-style female connector (only two of the pins are used). The connector is the same as what is found on the most servos and has a 0.1" spacing, so it fits nicely with 0.1" male headers and can plug directly into most RC receivers, servo extension cables, and servo switch harnesses, and custom cables made with JR male connectors or Futaba J male connectors. Note, however, that this style of connector is often referred to as “male” in the RC hobby industry, so please use the picture on the right to clear up any potential confusion.
Our rechargeable NiMH battery packs give you variety of options for powering your robot or electronics project. The battery packs use 1.2 V cells and are available in several capacities:
![]() |
| Cell Type | Capacity (mAh) |
|---|---|
| AA | 2200 |
| AAA | 900 |
| 2/3 AAA | 350 |
| 1/3 AAA | 200 |
The picture to the right shows the relative sizes of our NiMH battery packs. These packs are well-suited for powering small robots, and the smaller (1/3- or 2/3-AAA) battery packs make great power sources for miniature robots, such as those that might be based on our Baby Orangutan robot controller.
|
|
Battery pack color may differ from what is shown in the main product picture.
Note: The battery voltages listed in the product descriptions are based on the 1.2 V nominal voltage of the NiMH cells from which the packs are made. The actual voltage will depend on how charged the batteries are. A fully charged NiMH cell will deliver almost 1.5 V, so, for example, a “6V”, 5-cell pack can measure over 7 volts after being charged, and it can fall well below 5 volts when the pack is drained. You will need to charge these battery packs before you first use them. The iMAX-B6AC battery charger works well with these battery packs.
![]() |
Pololu Carrier with Sharp GP2Y0D810Z0F Digital Distance Sensor 10cm |
![]() |
Micro Maestro 6-Channel USB Servo Controller (Partial Kit) |
![]() |
Sub-Micro Servo 3.7g (Generic) |
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The Uni-T non-contact thermometer is designed to measure the temperature of the human body. It allows you to measure the temperature in a non-invasive way in the range from 32°C to 42.9°C from a distance of 5 to 10 cm. Uni-T UT300H
No product available!
Kit with 16 modules and the IO Expansion Shield designed to work with the Arduino Uno. Dedicated to learning programming and electronics
No product available!
Development kit with ESP32 WiFi and Bluetooth module and 1.54 "ePaper display. Built-in IMU MPU6050 sensor and USB-UART converter. LilyGO TTGO T-Block ESP32
No product available!
Programmable watch with ESP32-Pico-D4. Equipped with a touch button display, motion sensor, power management system, RTC clock and Lithium battery. LILYGO TTGO T-Wristband
No product available!
Wrist strap for LilyGo TTGO t-wristband module. Black colour
No product available!
Solar panel with an output voltage of 6 V and a power of 1 W. Provides high efficiency and work stability
No product available!
8 Mpx camera module with IMX219 sensor and wide-angle lens. To be used as a replacement on the RPI Camera Board V2. ArduCAM B0194
No product available!
The module with the OV5647 sensor, working with all versions of the Raspberry Pi. It uses a built-in movable IR-CUT filter that is turned on and off automatically depending on the lighting conditions. ArduCAM B003507
No product available!
Set of 4 mounting plates for Raspberry Pi 4B compatible with 19-inch 3U rack mount. The holder shown in the 3rd picture is not included in the set and must be purchased separately. ArduCAM U6131
No product available!
Camera module with IMX477 HQ sensor designed for Raspberry Pi Compute Module (CM3, CM3 +, CM4). Equipped with 1/2.3″ lens with M12 mount and 75° viewing angle. ArduCAM B0271
No product available!
Camera with a USB interface with a resolution of 8 MP. Equipped with a Sony CMOS IMX179 sensor and a wide-angle lens with a viewing angle of 105°. ArduCAM UB0229
No product available!
1 MPx camera module with OV9281 sensor that works with all versions of the Raspberry Pi. Equipped with a shutter and an IR filter, it is characterized by good sensitivity. ArduCAM B0225
No product available!
2 MPx camera module with OV2311 sensor working with Raspberry Pi. Equipped with a shutter and M12 lens mount. ArduCAM B0219
No product available!
2 MPx camera module with OG02B10 sensor that works with all versions of the Raspberry Pi. Equipped with a shutter, it is characterized by good sensitivity. ArduCAM B0199
No product available!
Camera module 8 MPx with IMX219 sensor and lens with a viewing angle of 75°. To be used as a replacement on the RPI Camera Board V2. ArduCAM B0188
No product available!
Module with 8 Mpx camera with IMX219 sensor and lens with 75° viewing angle. Designed for Nvidia Jetson Nano and Raspberry Pi Compute Module. ArduCAM B0187
No product available!