- Out-of-Stock
Rechargeable NiMH Battery Pack: 7.2 V, 2200 mAh, 3x2 AA Cells, JR Connector
This is a rechargeable 7.2 V NiMH battery pack with a capacity of 2200 mAh. The pack consists of six AA cells in two rows and a 4" lead terminated by a “JR”-style connector.
![]() |
This battery pack comes with 4" leads terminated by a 3-pin JR-style female connector (only two of the pins are used). The connector is the same as what is found on the most servos and has a 0.1" spacing, so it fits nicely with 0.1" male headers and can plug directly into most RC receivers, servo extension cables, and servo switch harnesses, and custom cables made with JR male connectors or Futaba J male connectors. Note, however, that this style of connector is often referred to as “male” in the RC hobby industry, so please use the picture on the right to clear up any potential confusion.
Our rechargeable NiMH battery packs give you variety of options for powering your robot or electronics project. The battery packs use 1.2 V cells and are available in several capacities:
![]() |
| Cell Type | Capacity (mAh) |
|---|---|
| AA | 2200 |
| AAA | 900 |
| 2/3 AAA | 350 |
| 1/3 AAA | 200 |
The picture to the right shows the relative sizes of our NiMH battery packs. These packs are well-suited for powering small robots, and the smaller (1/3- or 2/3-AAA) battery packs make great power sources for miniature robots, such as those that might be based on our Baby Orangutan robot controller.
|
|
Battery pack color may differ from what is shown in the main product picture.
Note: The battery voltages listed in the product descriptions are based on the 1.2 V nominal voltage of the NiMH cells from which the packs are made. The actual voltage will depend on how charged the batteries are. A fully charged NiMH cell will deliver almost 1.5 V, so, for example, a “6V”, 5-cell pack can measure over 7 volts after being charged, and it can fall well below 5 volts when the pack is drained. You will need to charge these battery packs before you first use them. The iMAX-B6AC battery charger works well with these battery packs.
![]() |
iMAX-B6AC Balance Charger and Discharger |
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
External case designed to protect, transfer and store data on M.2 SSD drives with SATA interface. GEMBIRD EE2280-U3C-01
No product available!
External enclosure designed to protect, transfer and store data on M.2 SSD drives with NVMe or SATA interface. Unitek S1204B
No product available!
Module with e-Paper display with a diagonal of 2.13" and a resolution of 250x122 px with WiFi communication and Bluetooth 4.2. Waveshare 2.13inch e-Paper Cloud Module
No product available!
LoRa module based on ESP32-WROOM-32E with WiFi and Bluetooth communication and LoRa RFM95W modem. There are ESP32 pins and a Qwiic connector on the board. SparkFun WRL-18074
No product available!
A module with a MEMS microphone and an amplifier that will allow you to detect a voice, a clap or a door slam. The board has an analog output. SparkFun BOB-18011
No product available!
Base board for the SpaceSOM-8Mplus family of modules. Creates a complete development platform similar to the SBC. SoMLabs SpaceCB-8Mplus-ADV v.1.1
No product available!
50 W soldering iron for Bakon BK950D station. Works with soldering tips from the T13 series
No product available!
HAT expansion module with SATA interface designed for Raspberry Pi 4 model B. It allows you to connect to a minicomputer mass storage in the form of 2.5" HDDs and SSDs with SATA interface
No product available!
HAT type power supply module with cooling fan designed for Raspberry Pi 4 model B. Provides flexible power supply to the minicomputer via DC 5.5x2.5 mm connector, XH2.54 mm connector, microUSB or USB type C connector
No product available!
Wall charger with USB and USB type C sockets. Supports QC3.0 + PD3.0 fast charging protocol with a maximum current of up to 3 A. USAMS US-CC085
No product available!
A spatula for removing prints from the 3D printer table. Made of stainless steel, it is durable and handy
No product available!
A needle with a diameter of 0.4 mm, designed for cleaning the nozzle in 3D printers. It allows you to get rid of the remnants of the material after printing and to remove the filament in case of clogged nozzle
No product available!
Aluminum tensometer beam, allowing weight measurement up to 2 kilograms. It has four wires. It is used in kitchen scales and portable scales
No product available!
Educational set for building robots based on Totem construction elements. Designed for beginners, it allows you to create 7 robot structures based on the included assembly instructions. Totem TKR-RK1
No product available!
Module with 17x7 LED matrix display (119 LEDs) designed to work with the Raspberry Pi. It uses the IS31FL3731 driver and communicates via the I2C interface. Pimoroni PIM331
No product available!
Module with 17x7 LED matrix display (119 LEDs) designed to work with the Raspberry Pi. It uses the IS31FL3731 driver and communicates via the I2C interface. Pimoroni PIM332
No product available!
Rechargeable NiMH Battery Pack: 7.2 V, 2200 mAh, 3x2 AA Cells, JR Connector