AT91SAM7S256-AU-001

The two-channel DDS signal generator supports a frequency range of up to 15MHz with a precision of up to 0.01uHz and DDS technology ensures signal stability. The device offers 12-bit vertical resolution, 1mV amplitude resolution and 50Ω output impedance. Junctek JDS6600-15

A two-channel DDS signal generator with a range of up to 40MHz ensures precise signal generation thanks to DDS technology with an accuracy of 0.01uHz. The device offers 12-bit vertical resolution, 1mV amplitude resolution and 50Ω output impedance, making it irreplaceable in electronics laboratories. Junctek JDS6600-40

The two-channel DDS signal generator with a frequency of 60MHz enables the generation of various waveforms, from a sine wave with a range of up to 60MHz to a pulse wave with a range of up to 6MHz. The device is distinguished by a precise frequency resolution of 0.01uHz, stability of 1ppm/3h and 12-bit waveform resolution. Junctek JDS6600-60

Vector network analyzer with two ports. It can perform measurements for frequencies from 50 kHz to 4.4 GHz. Equipped with an LCD display, it can be connected to a computer via USB. Nanovna V2 4"

Vector network analyzer with two ports. It can perform measurements for frequencies from 50 kHz to 3 GHz. Equipped with an LCD display, it can be connected to a computer via USB. NanoV2 3.2"

SDR (Software Defined Radio) receiver that allows you to receive signals in the frequency range from 10 kHz to 1 GHz. It is ideal for both monitoring low frequencies and receiving signals on higher bands

Thermal imaging camera module with an MLX90640 infrared sensor and a 2.8" TFT LCD display. It offers an accuracy of 2°C and a viewing angle of 55°x35°.

Antenna dedicated to communication in LoRa networks in the 868 MHz frequency band. Equipped with an RP-SMA connector. SparkFun WRL-18083

Visible spectrum emitter module that combines 9 discrete LEDs covering visible light wavelengths from 455 to 720 nm. It uses Qwiic connectors and I2C communication as well as a USB type C socket to power the module. SparkFun SPX-21316

WM8960 stereo codec module with driver for 1W class D speakers and headphones. It uses the I2S interface and the I2C bus to configure the system. SparkFun BOB-21250

MP3 player module controlled by I2C interface or switching inputs. It is based on a 1.4 W audio amplifier. The board has a 3.5 mm audio output and a connector for connecting a loudspeaker. Files are played from a microSD card. SparkFun DEV-19030

A set with an adapter dedicated to the FLIR Lepton thermal imaging camera and the Lepton FS camera. It has been pre-configured to operate as a plug-and-play UVC 1.0 USB camera, it can also communicate via UART and I2C interface. SparkFun DEV-20813

Motion detection module featuring Panasonic\'s EKM series PIR sensor. The EKM series is optimised for detecting small movements and is ideal for detecting movement in a small area around the sensor. It offers digital output in 32 zones with a detection distance of 5 m and a detection area of 90° x 90°. SparkFun SEN-22000

Antenna dedicated to communication in LoRa networks in the 868 MHz frequency band. Equipped with an RP-SMA connector. SparkFun WRL-18082

Sensor module for electromyography (EMG). Allows muscle activity to be studied and used to control devices. SparkFun DEV-21265

Portable soldering iron with a power of 65 W. It has an adjustable operating temperature in the range of 50 ° C to 400 ° C. It can be powered via a DC or USB type C connector. The set includes a soldering iron and a BC2 tip. MiniWare TS101 (BC2) Blue