- Out-of-Stock
131:1 Metal Gearmotor 37Dx57L mm
This 2.22" x 1.45" x 1.45" gearmotor is a powerful brushed DC motor with 131:1 metal gearbox intended for operation at 12 V. These units have a 0.61"-long, 6 mm-diameter D-shaped output shaft. This gearmotor is also available with an integrated encoder.
Key specs at 12 V: 80 RPM and 300 mA free-run, 250 oz-in (18 kg-cm) and 5 A stall.
This powerful brushed DC gearmotor is available in six different gear ratios. A version with an integrated encoder is also available.
| Gear Ratio | Speed @ 12V | Stall Torque @ 12V | Stall Current @ 12V | ![]() With Encoder | ![]() Without Encoder |
|---|---|---|---|---|---|
| 19:1 | 500 RPM | 84 oz-in | 5 A | 37Dx52L mm | 37Dx52L mm |
| 29:1 | 350 RPM | 110 oz-in | 5 A | 37Dx52L mm | 37Dx52L mm |
| 50:1 | 200 RPM | 170 oz-in | 5 A | 37Dx54L mm | 37Dx54L mm |
| 67:1 | 150 RPM | 200 oz-in | 5 A | 37Dx54L mm | 37Dx54L mm |
| 100:1 | 100 RPM | 220 oz-in | 5 A | 37Dx57L mm | 37Dx57L mm |
| 131:1 | 80 RPM | 250 oz-in | 5 A | 37Dx57L mm | 37Dx57L mm |
These motors are intended for use at 12 V, though the motor can begin rotating at voltages as low as 1 V.
The face plate has six mounting holes evenly spaced around the outer edge threaded for M3 screws. These mounting holes form a regular hexagon and the centers of neighboring holes are 15.5 mm apart. You can use our custom 37D metal gearmotor bracket (shown in the left picture below) to mount the gearmotor to your project via these mounting holes and the screws that come with the bracket.
|
|
Please note that unlike our smaller metal gearmotors, these 37D mm gearmotors have output shafts with a diameter of 6 mm. The Pololu universal aluminum mounting hub for 6mm shafts can be used to mount our larger Pololu wheels (80mm- and 90mm-diameter) or custom wheels and mechanisms to the gearmotor’s output shaft (see the right picture above).
The picture below shows the dimensions (in mm) of the 37D mm line of gearmotors. The value of X is 22 mm for the 19:1 37Dx52L mm and 29:1 37Dx52L mm versions, 24 mm for the 50:1 37Dx54L mm and 67:1 37Dx54L mm versions, and 26.5 mm for the 100:1 37Dx57L mm and 131:1 37Dx57L mm versions.
![]() |
| 37D mm metal gearmotor dimensions (units in mm). |
|---|
Warning: Do not screw too far into the mounting holes as the screws can hit the gears. We recommend screwing no further than 3mm (1/8") into the screw hole.
The operational specs listed in the table below were measured at 6 V. At 12 V, the no-load RPM, stall current, and stall torque will all be approximately twice their 6V values. To see the motor specs for 12V operation, please see the short description at the top of this page or this product’s specification tab.
![]() |
| 37D mm metal gearmotor next to a micro metal gearmotor for size comparison. |
|---|
We offer a wide selection of metal gearmotors that offer different combinations of speed and torque. Our metal gearmotor comparison table can help you find the motor that best meets your project’s requirements.
![]() |
| Some of the Pololu metal gearmotors. |
|---|
![]() |
Pololu Universal Aluminum Mounting Hub for 6mm Shaft Pair, 4-40 Holes |
![]() |
Pololu 37D mm Metal Gearmotor Bracket Pair |
![]() |
Pololu Jrk 21v3 USB Motor Controller with Feedback |
Manufacturer
Responsible person
TE0706 is a base plate for Trenz Electronic 4x5cm Muduors. It allows you to connect USB, JTAG and Ethernet interfaces. TE0706-02
No product available!
Base plate for Trenz Electronics modules 4 x 5 cm, eg for TE0741. The board allows connecting to the module interfaces: USB, Ethernet, JTAG, UART. TE0703-05
No product available!
USB TO UART solution with USB Type A connector, Waveshare
No product available!
No product available!
The second version of the clock synchronization signal receiver, transmitted with AM modulation (DCF77). The built-in MAS6180 system allows you to receive timing frames from a time pattern using a carrier frequency of 77.5 kHz. Thanks to this module, it is possible to create a clock with automatic date and time synchronization. The module has a ferrite antenna. modDCF77 v2
No product available!
Pyboard is a compact development board that allows you to use the MicroPhyton software. Min. 3-axis accelerometer (MMA7670), diodes, monostable buttons and microSD memory card slot. Adafruit 3497
No product available!
LCD touch screen with 160x128 pixel resolution, LCD160CR (I2C or UART and SPI) display controller. Adafruit 3498
No product available!
Module with Xilinx Kintex-7 XC7K325T-2CF system, 32MB FLASH memory and very fast data transmission systems. Everything is on a small 4 x 5 cm plate. TE0741-03-325-2CF
No product available!
Module with Xilinx Artix-7, USB 3.0 / FIFO bridge, 1GB DDR3L SDRAM memory, 32 MB flash memory and pulse converters to ensure all voltages in the system. Everything fits on a small 4 x 5 cm tile. TE0713-01-100-2C
No product available!
Module with Xilinx Artix-7, USB 3.0 / FIFO bridge, 1GB DDR3L SDRAM memory, 32 MB flash memory and pulse converters to ensure all voltages in the system. Everything fits on a small 4 x 5 cm tile. TE0713-01-200-2C
No product available!
Desktop computer kit with expansion board that can turn a Raspberry Pi into a real desktop PC.
No product available!
BB Black Expansion CAPE, Features RS485 and CAN Interfaces
No product available!
32-bit microcontroller with ARM Cortex-M4 core, Ultra-low-power, 144 pins, 1 MB Flash, 320 KB SRAM, temperature range -40 ... 85 ° C, LQFP144, STMicroelectronics, RoHS
No product available!
NVIDIA development kit with the Tegra X2 SoC chip containing two Denver cores, four 64-bit ARM Cortex A57 cores and a Pascal graphic layout consisting of 256 cores supporting CUDA technology. Jetson TX2 Development Kit
No product available!
A set of PCBs with a programmed layout for the LED thermometer - version 27mm green. AVT1697 / 2 / G A +
No product available!
AVT kit for self-assembly of the LED thermometer - 27mm green version. AVT1697 / 2 / GB
No product available!
131:1 Metal Gearmotor 37Dx57L mm