- Out-of-Stock
MPL115A1 Barometric Pressure Sensor Breakout Board
The MPL115A1 is a MEMS digital barometer that takes barometric pressure readings with a range of 50 to 115 kPa and an accuracy of ±1 kPa and provides the results over an SPI interface. This sensor also doubles as a temperature sensor that operates from -40 to 105 °C. The breakout board’s pins are spaced 0.1" apart making it easy to use with standard breadboards and 0.1" perfboards.
![]() |
The MPL115A1 MEMS digital barometer carrier board from SparkFun takes ±1 kPa accurate pressure readings with a range of 50 to 115 kPa. The barometric pressure sensor makes the readings available via SPI. The pressure sensor’s average current consumption is 10ěA at one measurement per second. The sensor doubles as a temperature sensor that operates from -40 to 105 °C. The breakout board’s pins are spaced 0.1" apart making it easy to use with standard breadboards and 0.1" perfboards.
See page 3 of the MPL115A1 datasheet (228k pdf) for information on how to take readings from this barometric pressure and temperature sensor. SparkFun also provides AVR ATMega328 C code for interfacing with the MPL116A1 (17k zip).
|
|
![]() |
HIH-4030 Humidity Sensor Carrier |
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Power Supply 2.5A 5.1V for Raspberry Pi 3 model B - STONTRONICS T5875DV
No product available!
Pre-installed Ubuntu 14.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode
No product available!
No product available!
No product available!
Pre-installed Ubuntu 14.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode
No product available!
Pre-installed Android 4.x or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode
No product available!
3.2D soldering tip, flat screwdriver 5.5mm in diameter, for WEP 926 soldering station
No product available!
Pre-installed Ubuntu 14.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode
No product available!
5V / 3.1A eXtreme power supply with microUSB plug for all Raspberry Pi computers (including Pi 3 model B and Pi 3 model B +)
No product available!
Antenna with built-in LNA amplifier with high sensitivity, for mounting in a device using a GPS module. The antenna has a 25mm cable, terminated with a U.FL plug (IPEX). Dimensions of the device: 9 x 9 x 4mm
No product available!
The GY-GPS6MV1 module is a board containing the U-blox NEO-6M GPS receiver system. The tile also includes RTC backup battery, antenna connector (U.FL), voltage stabilizer and UART signal outputs
No product available!
Kit: MAXimator, MAXimator Expander, ZL32PRG - USB Blaster PRO
No product available!
Power Supply 2.5A 5.1V for Raspberry Pi 3 model B - STONTRONICS T5875DV
No product available!
MYD-JA5D44 Development Board is a complete educational platform. Its heart is the MYIR MYC-JA5D44 module, which was equipped with the Atmel SAMA5D44 processor based on Cortex-A5 cores. The processor can work at a maximum frequency of 600 MHz. Min. RS232, RS485 connectors, HDMI connector, 3.5 mm Jack Audio inputs, microSD memory card slot, 10/100 Mbps Ethernet slot and many more.
No product available!
The Raspberry Pi GPIO Triple Expansion Board converts the single GPIO headers on your Raspberry Pi into three parts. DFR0385
No product available!
Flex Cable for Raspberry Pi Camera - 300mm / 12". Adafruit 1648
No product available!
MPL115A1 Barometric Pressure Sensor Breakout Board