- Out-of-Stock
EL Flowing Effect Wire with Inverter - Blue 2.0 meter (6.5 ft)
ID: 203128
Adafruit 948 - EL Flowing Effect Wire with Inverter - Blue 2.0 meter (6.5 ft)
948 - EL Flowing Effect Wire with Inverter - Blue 2.0 meter (6.5 ft)
This pack comes with 2 meters of EL flow wire attached to a 2xAA inverter, use any AA batteries (alkalines are better and brighter but it works fine with NiMH rechargeables). Theres a belt clip on the inverter so you can attach it to something. This EL type isnt meant to be cut and re-soldered because of the triple-core so keep in mind that you can cut it short but we dont suggest trying to splice or re-solder to the wire. Runs for about 5 hours off of two AA batteries.
Please note! EL tape, EL wire and EL panel are made with different processes - the color and brightness will not be consistent between the different types of EL products. The EL flow wire will not match the regular EL wire, EL tap or EL panel exactly, they all will be slightly different colors.
Description
If you want to make your EL project a little more dynamic, you can swap in this nifty flowing effect EL wire for the every-day stuff. Instead of a single core, this wire is actually a bundle of three thin EL wires. Inside the inverter is a little timer that will cycle through the strands to make it look like its moving. Theres a wheel to adjust the speed and a button to select the mode. The three modes are all on, all off and flow effect.This pack comes with 2 meters of EL flow wire attached to a 2xAA inverter, use any AA batteries (alkalines are better and brighter but it works fine with NiMH rechargeables). Theres a belt clip on the inverter so you can attach it to something. This EL type isnt meant to be cut and re-soldered because of the triple-core so keep in mind that you can cut it short but we dont suggest trying to splice or re-solder to the wire. Runs for about 5 hours off of two AA batteries.
Please note! EL tape, EL wire and EL panel are made with different processes - the color and brightness will not be consistent between the different types of EL products. The EL flow wire will not match the regular EL wire, EL tap or EL panel exactly, they all will be slightly different colors.
- 2 meter long EL cord, 3mm thick
- Flow effect can go as slow as 30 Hz
203128
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
The portable power supply for electroluminescent wires is powered by two AA (R6) batteries, it has a built-in diode signaling the operating mode and a power supply output in the form of a wire terminated with a JST connector. The device also has a clip that allows you to hang them on trousers
zł11.76
24h
Available quantity: 9
Available
Other products in the same category (16)
Assembled alarm control panel cooperating with the motion sensor. AVT1925 C
Retired
No product available!
AVT kit for self-assembly of the power distributor. AVT1930 B
Retired
No product available!
Assembled power divider, designed to supply several receivers from one voltage source with more power. AVT1930 C
Retired
No product available!
High quality XF-ABS filament for 3D printer with 1.75 mm diameter. 1 kg of wire is wound on the spool. XF-ABS-175-GRAY
Retired
No product available!
Flexible PVC cover for 6M3 connector, for ØD = 3.5mm cable, length L = 24mm, width W = 6.5mm, black, RoHS
24h
Available quantity: 20
No product available!
The AM receiver of the DCF77 signal with the MAS6180 system, allows to receive the frames of the synchronization signal from the time standard, using the carrier frequency of 77.5kHz. Thanks to this module, it is possible to create a clock with automatic date and time synchronization. The module has a ferrite antenna. modDCF77
Retired
No product available!
Module with Tegra X1 SoC system containing four 64-bit ARM Cortex A57 cores and a Maxwell graphic layout consisting of 256 cores supporting CUDA technology. NVIDIA Jetson TX1
Retired
No product available!
Arducam-F Rev.C+ Camera module shield with OV2640 for Arduino UNO MEGA2560 DUE. ArduCam B0051+B0011
Retired
No product available!
Arducam-LF Rev.C+ Camera module + 3.2 inch LCD for arduino UNO MEGA2560 DUE. ArduCam B0052+B0011
Retired
No product available!
Module designed for connecting more than one camera to a single CSI camera port on RPi board. One adapter board can connect 4 cameras and user can stack up max. 4 adapter boards that means up to 16 cameras on a single RPi board. ArduCAM B0069
Retired
No product available!
5mp 1080p OV5647 NoIR Camera Module with M12*0.5 Mount Lens for Raspberry Pi. ArduCam B0035
Retired
No product available!
OV5647 Camera Board with LS-40180 Fisheye Lens M12x0.5 Mount for Raspberry Pi 3. ArduCam B0055
Retired
No product available!
Open source WIFI camera develop board based on Texas Instruments CC3200 SimpleLink WIFI IoT solution and Aptina MT9D111 camera module. ArduCAM B0073
Retired
No product available!
No product available!
Gravity: GPIO Shield for Arduino is an I / O port expander compatible with Arduino UNO. It allows to expand the capabilities of the base board by providing a total of 36 digital and analogue pins as well as UART and I2C interfaces. DFRobot DFR0334
Retired
No product available!
Adafruit 948 - EL Flowing Effect Wire with Inverter - Blue 2.0 meter (6.5 ft)