- Out-of-Stock
JTAG SMT2 Surface-Mount Programming Module, Digilent, RoHS
The Joint Test Action Group (JTAG)-SMT2 is a compact, complete and fully self-contained surface-mount programming module for Xilinx field-programmable gate arrays (FPGAs). The module can be accessed directly from all Xilinx tools, including iMPACT, Chipscope, and EDK. Users can load the module directly onto a target board and reflow it like any other component.
The JTAG-SMT2 uses a 3.3V main power supply and a separate Vref supply to drive the JTAG signals. All JTAG signals use high speed, 24mA, three-state buffers that allow signal voltages from 1.8V to 5V and bus speeds of up to 30MBit/sec. The JTAG bus can be shared with other devices as systems hold JTAG signals at high-impedance, except when actively driven during programming. The SMT2 module is CE certified and fully compliant with EU RoHS and REACH directives. The module uses a standard Type-A to Micro-USB cable available for purchase from Digilent, Inc.
Users can connect JTAG signals directly to the corresponding FPGA signals as shown in Figure 1. For best results, mount the module adjacent to the edge of the host PCB over a ground plane. Although users may run signal traces on top of the host PCB beneath the SMT2, Digilent recommends keeping the area immediately beneath the SMT2 clear. Note: Keep the impedance between the SMT2 and FPGA below 100 Ohms to operate the JTAG at maximum speed. The SMT2 improves upon the SMT1 with the addition of three general purpose IO pins (GPIO0 – GPIO2) and support for interfacing IEEE 1149.7-2009 JTAG targets in both 2 and 4-wire modes.
Key Features:
Download:
Code: 210-251

Manufacturer
Responsible person
No product available!
USB compatible cable for in-circuit configuration and programming of all Xilinx devices
Metal case dedicated to the Odroid M1 minicomputer. Hardkernel M1 Metal case Kit
No product available!
MicroMod main module with Alorium Sno M2 chip. Equipped with an M.2 connector, it can work with MicroMod expansion boards. SparkFun DEV-18030
No product available!
Module with a temperature sensor designed for the M5Stack sets. It allows you to measure high temperatures. The set includes a K-type thermocouple probe. M5Stack U133
No product available!
M5Stack series development kit equipped with ESP32. It will work in IoT-related projects, as a STEM educational module or in Smart Home devices. M5Stack K001-V26
No product available!
Compact development kit from the M5StickC series equipped with ESP32 Pico and display. Includes accessories for building a watch. M5Stack K016-H
No product available!
M5Stack series development kit equipped with ESP32 chip. It has a built-in microphone and is dedicated to applications that require speech recognition. M5Stack K117
No product available!
The module with 4 relays is designed for the M5Stack sets. It allows you to control devices with an operating voltage of up to 250 V AC and a current of up to 10 A or a voltage of 28 V DC and a current of 10 A. M5Stack U097
No product available!
Flash eMMC module for Odroid M1 computers by Hardkernel. 8 GB capacity, Linux operating system installed. The set includes a microSD adapter. Hardkernel 8GB eMMC Module M1 Linux
No product available!
Flash eMMC module for Odroid M1 computers by Hardkernel. 128 GB capacity, Linux operating system installed. The set includes a microSD adapter. Hardkernel 128GB eMMC Module M1 Linux
No product available!
Flash eMMC module for Odroid M1 computers by Hardkernel. 128 GB capacity, Android operating system installed. The set includes a microSD adapter. Hardkernel 128GB eMMC Module M1 Android
No product available!
Starter kit containing Raspberry Pi 4B 2 GB and all necessary accessories: 32 GB microSD memory card with Rasberry Pi OS system, Ethernet cable, official accessories: housing, cooling kit, power supply and HDMI cable and ruler
No product available!
Kit containing Raspberry Pi 4B 4GB, 32GB microSD card with Rasberry Pi OS, ruler, Ethernet cable and official accessories, housing, cooling kit, power supply and HDMI cable
No product available!
LED strip with COB diodes in red. It is powered by 12 V DC, has a length of 5 m and 384 LEDs/m. Protection level IP20
No product available!
Universal silicone cover that protects the LED strip against moisture, water and dirt. Provides protection in accordance with the IP67 standard
No product available!
Universal silicone cover that protects the LED strip against moisture, water and dirt. Provides protection in accordance with the IP67 standard
No product available!
Universal silicone cover that protects the LED strip against moisture, water and dirt. Provides protection in accordance with the IP67 standard
No product available!
JTAG SMT2 Surface-Mount Programming Module