- Out-of-Stock
9V stabilizer with 500mA protection
ID: 557550
5906623411122
The stabilizer module is used to stabilize the output voltage at an appropriate level and filter interference. The module can be supplied with voltage up to + 16V, and the output voltage is + 9V. MOD-06 / 9V.Z
Description
Electronic devices require power with a certain voltage value. The stabilizer is used to stabilize the output voltage at an appropriate level and filter interference. The module can be supplied with voltage up to + 16V, and the output voltage is + 9V.
For example, if a voltage stabilizer is connected to the + 12V power supply, then on its output we get +9 V (also other voltage values are available) that we can use to power the microcontroller.
The module has a built-in protection of 500mA. If the current exceeds this value, the fuse will operate and the output will be disconnected. In this case, just disconnect the power supply to reset the protection, there is no need to replace the fuse.
Technical data
- Code and name of the module: MOD-06 / 9V Stabilizer 9V with protection
- Integrated circuit: LM7809
- Protection: 500mA polymer fuse
- Power: up to + 16V
- Output voltage: + 9V
- LED signaling: yes
- Dimensions: 39 mm x 16 mm
- Additional information: built-in filter capacitors for higher load currents and a large difference between the supply voltage and the output voltage, it may be necessary to use a heat sink for heat dissipation
- RoHS: yes
Set contains
- assembled MOD-06 / 9V.Z 9V stabilizer with protection
- set of connectors for self-assembly (ARK screw connection - 2 pcs.)
To download
557550
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
MYIR MYC-SAMA5D36 is a single board computer in the form of a card with SO-DIMM 200-pin connector. It has been equipped with the SAMA5D36 processor from Atmel, based on Cortex-A5 cores. It can work with a maximum frequency of 536 MHz. It has 512 MB DDR2 SDRAM, 256 MB NAND FLASH memory. GPIO ports, interfaces have been derived on the SO-DIMM 200-pin connector
Retired
No product available!
8-bit ST7 MCU, 8kB Flash, 384B RAM, Lite Timer, Autoreload Timer, SPI, LINSCI, 10-bit ADC, DIP20, RoHS
Retired
No product available!
No product available!
No product available!
Kit for building an intelligent JetBot robot based on Jetson Nano. It consists of Jetson Nano with 4GB RAM, expansion module, WiFi card, camera, motors, housing and a set of mounting screws. JetBot AI Kit (USB WiFi) 4GB
Retired
No product available!
HK Turnigy HD 3508 Brushless Gimbal Motor (BLDC) (45367)
Retired
No product available!
No product available!
No product available!
A module that allows you to connect ArduCAM cameras with a CSI interface to a PC or minicomputers via the USB3.0 interface. It not only supports high-resolution, high-frame rate image sensors, but also a stereoscopic camera and IRCUT control functions. ArduCAM B0111
Retired
No product available!
No product available!
Arduino M0 PRO (M0+ Atmel processor) with build in companion chip to let you debug your application
Retired
No product available!
No product available!
The ISM radio module in the SMD housing. It operates on the 868 MHz frequency. The module complies with FCC, ETSI regulations. HOPE MICROELECTRONICS RFM12B-868S2P
Retired
No product available!
Akira Chiba, Tadashi Fukao, Osamu Ichikawa, Masahide Oshima, Masatugu Takemoto, David Dorrell
Delivery date unknown
No product available!
Bluetooth 5.1 module (BLE, SPP) designed to work with the Raspberry Pi Pico. It communicates via the UART interface using AT commands. Waveshare Pico-BLE
Retired
No product available!
No product available!
The stabilizer module is used to stabilize the output voltage at an appropriate level and filter interference. The module can be supplied with voltage up to + 16V, and the output voltage is + 9V. MOD-06 / 9V.Z