- Out-of-Stock
RS485 Shield V2 - module for Raspberry Pi
ID: 558626
Extension for Raspberry Pi; communication module with RS-485 interface (DEV-13000). Module with the possibility of mounting the DB-9 socket, the socket should be purchased separately
RS485 Shield V2 - Raspberry Pi
Description:
Our friends over at LinkSprite have this little nifty RS485 Shield V2 for the Raspberry Pi, now you can connect to your RPi! Even though the RS485 is sometimes thought as an "archaic" protocol, it will allow up to a maximum of 10Mbit / s. Those are not bad numbers!
This shield comes pre-assembled so it's right for your Raspberry Pi and get programming. The RS485 Shield V2 is compatible with Raspberry Pi B, B + and Raspberry Pi 2.
Note: The shield has an unpopulated footprint for a DB9 connector. Check below if you need to add the connector. Otherwise you can use the screw terminals.
Documents:
558626
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
AVT kit for self-assembling LEDs, contains a set of elements. AVT1844 B
Retired
No product available!
Assembled AVT set, Christmas, shining Christmas tree LED. AVT1844 C
Retired
No product available!
The sensor detects dangerous carbon monoxide and carbon monoxide, signals a gas leak and the presence of carbon monoxide in rooms. URZ0409
Retired
No product available!
Female-female 10-core connection cable, 15 cm long with connectors of 1.27 mm pitch. Adafruit 1675
Retired
No product available!
32GB microSDHC Memory Card with SD Adapter, class 4, Kingston
Delivery date unknown
No product available!
Development kit chipKIT DP32 equipped with PIC32MX250F128B microcontroller (40/50 Mhz, 128 kB Flash, 32 kB RAM), prototype area with solder pads, potentiometer, 4 LED diodes, 2 buttons and soldering pads for EEPROM memory and analog temperature sensor. Digilent 410-280P-KIT
Retired
No product available!
large 14x21 hole prototyping area on an expansion card compatible with the myRIO Expansion Port (MXP). 6002-210-008P
Retired
No product available!
Perfect for connecting devices using Wi-Fi, Ethernet and Power over Ethernet options, the Yun combines an ATmega32u4 microcontroller with a Linux based Linino WiFi System on Chip module. A000003
Retired
No product available!
LPCXpresso4337 starter board with a dual-core LCP4337 microcontroller (Cortex-M4F + Cortex-M0 +). The set is equipped with a built-in programmer, buttons, diode, SPI Flash quad flash and USB - UART konwetrer
Retired
No product available!
Starter board LPCXpresso18S37 with LPC18S37 microcontroller (Cortex-M3). The set is equipped with a built-in programmer, buttons, diode, SPI Flash quad flash and USB - UART konwetrer
Retired
No product available!
Aluminum extensometer beam, allowing weight measurement up to 100 kilograms. It has four wires. It is used in kitchen scales and portable scales, max 100 kg, 20x23x94, 21 cm cable, RoHS
Retired
No product available!
High quality XF-ABS filament for 3D printer with 1.75 mm diameter. 1 kg of wire is wound on the spool. XF-ABS-175-GRAY
Retired
No product available!
The DDS generator with a readable alphanumeric display allows you to generate sinus, rectangular or triangle waveforms. The device can also be used for frequency measurement in the 1Hz-60MHz range
Retired
No product available!
ZigBee development/evaluation kit designed for CC2530F256
Retired
No product available!
Motor Control Shield, drives DC Motors & Stepping Motors
Retired
No product available!
EMW3162 WIFI Shield consists of a base plate and WiFi module EMW3162. Works with Arduino and STM32 Nucleo. Built-in USB-UART converter
Retired
No product available!
Extension for Raspberry Pi; communication module with RS-485 interface (DEV-13000). Module with the possibility of mounting the DB-9 socket, the socket should be purchased separately