- Out-of-Stock
Tensometric beam with a maximum load of 1 kg
ID: 558702
5906623454822
Aluminum extensometer beam, allowing measurement of weight up to 1 kilogram. It has four wires. It is used in kitchen scales and portable scales.
Description
Aluminum strainer beam, mounted on screws (not included), screwed in with threaded holes. The beam allows you to measure weight up to 1 kilogram. It has four wires.
The importance of wire colors
- red ("+" DC boost power)
- black ("-" DC boost power)
- white ("+" output signal)
- green ("-" output signal)
properties
- Weight measurement up to 1 kg
- Supply voltage: recommended 5-12 V DC, maximum: 15 V DC
- Input resistance: 1115 Ω
- Output resistance: variable (no load: 1000 Ω)
- Cable length: 25 cm
- Dimensions: 13 x 13 x 80 mm
558702
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Aluminum extensometer beam, allowing measurement of weight up to 20 kilograms. It has four wires. It is used in kitchen scales and portable scales, it has a 21 cm cable, RoHS.
zł41.88
Delivery date unknown
No product available!
The module allows you to attach a strain gauge (working in the Wheatstone bridge circuit) and convert the analog signal into its digital representation, available on the module output lines. The system processes the signal with a 24-bit resolution and can be powered by 2.7V - 5.5V. The module is especially recommended for constructing digital scales in combination with Arduino
zł4.59
24h
Available quantity: 47
Available
Other products in the same category (16)
Linklt Smart 7697 is an IoT module with a WiFi interface based on the Media76 system of MT7697. It is equipped with Wi-Fi, Bluetooth and many peripherals, including UART, I2C, SPI, I2S, PWM, IrDA and auxiliary ADC. Seeed Studio 102990803
Retired
No product available!
No product available!
No product available!
No product available!
No product available!
A printed circuit board and a programmed system for an audio potentiometer with a relay controlled by any remote control. AVT3222 A +
Retired
No product available!
AVT kit for self-assembly of a radio controlled audio potentiometer with a relay. AVT3222 B
Retired
No product available!
Assembled, controlled by any remote control, an audio potentiometer with a relay. AVT3222 C
Retired
No product available!
No product available!
No product available!
Real time clock (RTC) module. It allows you to read data about the date and time. Communication with the module takes place via the I2C interface. SparkFun BOB-14558
Retired
No product available!
Module with a differential I2C transceiver allowing to extend the range of the I2C communication bus. The differential signals are sent over an Ethernet cable that plugs into the RJ-45 connector. SparkFun BOB-14589
Retired
No product available!
Module with an absolute pressure sensor LPS25HB. The system is characterized by wide measuring range from 260 to 1260 hPa and high measurement resolution (0.01 hPa). I2C or SPI communication. SparkFun SPX-14767
Retired
No product available!
A set for self-assembly of a game console. Supports such emulators as Game Boy, Game Boy Color, Game Gear, Nintendo Entertainment System and Sega Master System. The kit can also be programmed using Arduino IDE, MicroPython. Odroid-GO
Retired
No product available!
The fan designed for use with the Digilent ZYBO Z7-20 plate mounted on the heat sink allows better air flow, which results in lowering the FPGA temperature. The fan has a 3-pin connector, the supply voltage is 5 V. In addition to the fan, there are screws for fixing. Digilent 240-130
Retired
No product available!
Starter kit with NanoPi NEO minicomputer. The set includes a NanoPi NEO 512MB minicomputer, an aluminum housing, a NanoHat OLED display, a MicroUSB cable, a heat sink, an 16GB memory card and the necessary mounting hardware. FriendlyELEC NEO Metal Complete Kit
Retired
No product available!
Aluminum extensometer beam, allowing measurement of weight up to 1 kilogram. It has four wires. It is used in kitchen scales and portable scales.