- Out-of-Stock
The cable that outputs the signals of the ATMEL ICE programmer
ID: 559297
The cable allows connecting the ATMEL-ICE programmer to the commissioning set with any connector (operated by the programmer), through individual pin connectors
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
*** A new version of the cable (v2) is available.
Click to go to the product page ***
Description
With this cable you can connect the ATMEL-ICE programmer to the development boards - it is easy to program a board with a 6-pin, 10-pin, JTAG or SAM connector.
The ATMEL-ICE programmer has signals in a 50 millisecond grid slot - it is very difficult to connect any wire from outside the programmer set. The offered cable solves this problem, giving the possibility of connecting any of the wires to any place on the development board.
properties
- Cable with 2x5 pin 50 miles connector -> 10 single female plugs
- Cord in the form of elastic ribbon
- Length: 20 cm
- Fits the AVR and SAM connectors of the ATMEL-ICE programmer
Attention!
Cable No. 10 is marked with a red stripe!
An example of using the cable for connecting ATMEL-ICE with the ZL15AVR board
An example of using an ATMEL-ICE cable with a KAmduino UNO PCB
Included
- The cable for the ATMEL-ICE programmer
To download
559297
You might also like
ATATMEL-ICE-BASIC is a programmer designed to work with AVR microcontrollers with the On-Chip Debug function and microcontrollers with the ARM Cortex-M core from Atmel. Available interfaces are JTAG, SWD, PDI, TPI, aWire, SPI and debugWire.
zł998.97
24h
Available quantity: 6
Available
ATATMEL-ICE-PCBA is a programmer in the form of a printed circuit board (without a casing), designed to work with AVR microcontrollers with the On-Chip Debug function and microcontrollers with the ARM Cortex-M core from Atmel. Available interfaces are JTAG, SWD, PDI, TPI, aWire, SPI and debugWire.
zł579.00
24h
Available quantity: 2
Available
Other products in the same category (16)
No product available!
No product available!
No product available!
A small current sense module with a digital SPI interface. The board combines an Allegro ACS722 Hall Effect current sensor with a 12-bit analog-to-digital converter. 410-325
Retired
No product available!
No product available!
HALLOTRON DC CURRENT INDICATOR - PRINTED PLUG AND PROGRAMMED SYSTEM
Delivery date unknown
No product available!
Base plate for Trenz Electronics modules 4 x 5 cm, eg for TE0741. The board allows connecting to the module interfaces: USB, Ethernet, JTAG, UART. TE0703-05
Retired
No product available!
No product available!
No product available!
No product available!
This compact, inexpensive plastic gearmotor (brushed DC motor with a 120:1 reduction gearbox) is well suited for use in small robots. While intended for operation at 4.5 V, it should run comfortably in the 3 V to 6 V range.
Retired
No product available!
AVT3193 A - modular listening receiver for the 80m and 40m Dosia bands. Power supply + 9V / + 5V,...
PCB printed to the modular listening receiver for the 80m and 40m Dosia bands. Power supply + 9V / + 5V. AVT3193 A
Retired
No product available!
Panasonic Eneloop R03/AAA rechargeable batteries with a capacity of 800mAh and a voltage of 1.2V. The set contains eight pieces sold in a reusable packaging. Panasonic BK-4MCCE/8LE
Retired
No product available!
No product available!
No product available!
No product available!
The cable allows connecting the ATMEL-ICE programmer to the commissioning set with any connector (operated by the programmer), through individual pin connectors