.png)
- Out-of-Stock
STMPS2141STR - 2.7-5.5 V power switch 500/1000 mA
ID: 559527
The STMPS2141STR system is a power switch designed for circuits with high capacitive loads and short circuits. The system is equipped with an N-channel MOSFET 90 mΩ controlled by the input logic level.
Description
The STMPS2141STR power supply switch is designed for circuits with high capacitive loads and short circuits. If the output current exceeds the limit, the system will switch to the constant current mode, while if the circuit starts charging too high current or there is a short-circuit, thermal protection will activate, which will switch the system off to prevent damage. After the system has cooled down to its normal temperature, the system will be switched on automatically. The switch can conduct a maximum current of 500 mA in continuous mode or 1000 mA of instantaneous current. The system operates on voltages from 2.7 V to 5.5 V. When in sleep mode, it draws a maximum of 12 μA.
Specification
- Maximum current: 500/1000 mA
- Power supply: 2.7 - 5.5 V
- Maximum power consumption in idle mode: 12 μA
- Housing: SOT23
- Protection against low voltage
- Protection against overheating and entering with a feedback signal
- ESD 8 kV protection
- Backfeed protection
- Working temperature: -40~85 ° C
559527
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
You might also like
Integrated Load Switch, SSOT6, Fairchild Semiconductor, RoHS
zł3.27
Delivery date unknown
No product available!
Controlled by logical levels power switch with adjustable current limit and protection against too low / too high voltage, excessive current or overheating. Power supply from 3 V - 5.5 V, housing WLCSP-9. NX5P2190UKZ
zł9.82
24h
Available quantity: 6
Available
Other products in the same category (16)
Aluminum extensometer beam, allowing weight measurement up to 3 kilograms. It has four wires. It is used in kitchen scales and portable scales.
Retired
No product available!
Aluminum extensometer beam, allowing mass measurement up to 5 kilograms. It has four wires. It is used in kitchen scales and portable scales.
Retired
No product available!
A two-wire, serial extender for I2C bus, SMBus and HDMI DDC, working at 2.7 V - 5.5 V. The system has a TSSOP8 housing. PCA9507DP
Retired
No product available!
32-bit microcontroller from the STM32F7 family with ARM Cortex-M7 core, 512kB Flash memory, 320kB SRAM, I2C, SPI, UART / USART memory, USB, CAN, 1.71 ... 3.6V, 100LQFP, STM, RoHS
Retired
No product available!
The 32-bit microcontroller from the STM32F7 family with the ARM Cortex-M7 core, has 1024 kB Flash memory and 320kB SRAM memory. Supports LCD-TFT, USB OTG HS, Ethernet, CAN, UART, I2C, SPI, ADC, DAC. System in the 144-LQFP housing. STM32F746ZGT6
Retired
No product available!
The set allows introducing distance, ambient lighting and gesture analysis into the subject using the VL6180X sensor. NUCLEO-L053R8 plate in set with VL6180X expansion board. P-NUCLEO-6180X2
Retired
No product available!
Shield for STM32 Nucleo, has two MP34DT01-M digital microphones made in MEMS technology
Retired
No product available!
9-inch display with universal HDMI interface and 10-point multitouch capacitive screen
Retired
No product available!
Load Cell Amplifier is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. SEN-13230
Retired
No product available!
Shadow Chassis is a marvelously durable and modular robot platform from RobotZone. The chassis plates and mounts are cut from ABS plastic and utilize the Actobotics 0.77" and 1.50" hub patterns for sensors, controllers, power, etc. With the included “snap on” micro-controller mounts, you can attach an Arduino, Raspberry Pi, SparkFun RedBoard, or SparkFun RedBot Mainboard!
Retired
No product available!
Bluetooth module for mounting in SMD technology with a fully configurable UART interface - transfer speed up to 2 Mb / s. WRL-11786
ATTENTION! A newer version of this product is available.
Click to go to the product page
Retired
No product available!
The LCD Button Shield V2 attaches to your Arduino to provide a 16x2, black character, green back light LCD with a keypad consisting of 5 keys — select, up, right, down and left. With this shield you will be able to move through menus and make selections straight from one board attached to your Arduino without requiring a massive tower of shields. DEV-13293
Retired
No product available!
No product available!
Nintendo DS Screen Kit joins two of our more unique products together to provide you with an easy means to equip your next project with touchscreen functionality. Inside each kit is one Nintendo DS Touchscreen and one SparkFun Touchscreen Connector Breakout. LCD-13631
Retired
No product available!
MG2639 SparkFun Cellular Shield is a perfect addition to any Arduino project that requires connectivity when there’s no WiFi or Ethernet access nearby. The ZTE MG2639 module, which this shield is built around, supports SMS, TCP, UDP, and can even be used to make or receive phone calls. CEL-13120)
Retired
No product available!
Imagine an Arduino Shield that can be configred to be an LCD, GPS, Wuifi, or any shield you may think of!
Delivery date unknown
No product available!
The STMPS2141STR system is a power switch designed for circuits with high capacitive loads and short circuits. The system is equipped with an N-channel MOSFET 90 mΩ controlled by the input logic level.