iNode LAN Camera - 5MPx camera with JPEG compression with BLE functionality

Description

iNode LAN Camera is a combination of 5MPx camera with JPEG compression with full BLE functionality (Bluetooth Smart, IoT - Internet of Things), as in iNode-LAN . With the iNode LAN Camera you can easily associate an iNode Beacon ID user with a registered photo (access control) or start recording if, for example, an iNode Care Sensor # 1 sensor reports an alarm to open a door to a room or iNode Care Sensor # 5 will detect a car in front of the gate.

You can see the image transmission on-line from the iNode LAN Camera here. Resolution 1920x1080, refresh every 15 seconds.

iNode LAN Camera uses HTTP / POST protocol for transmission over the Internet or LAN, thanks to which it can easily register images even on free virtual servers or cheap network drives. In order to ensure the privacy of such saved content, each JPEG image is encrypted with the ARCFour algorithm with another 128 bit temporary key. This key is coded by the cryptographic system in the AES128 algorithm (there is no way to read the main key once from the device) and entered into the header of the JPEG image. The JPEG images are decrypted directly in the user's browser. Without knowledge of the primary key, no unauthorized person has the opportunity to see such registered content. The potential-free output can be switched on / off remotely (via LAN) permanently or generate an impulse with a defined duration. By default, the device has DHCP enabled - this way it obtains the address in the 10 / 100Mbps LAN. The UPnP protocol is built into the device to the extent that it allows Windows to search for the device and show it in My Network Places.

properties

Bluetooth Low Energy and ethernet

• Configurable by browser:
  • The power with which the device works in BLE in the range from -18dBm to + 8dBm
  • LAN network parameters - IP address (fixed or by DHCP), network mask, gateway, DNS server, NTP time server
  • device name
  • IP address and port to which UDP packets are sent; sending method: multicast, unicast or broadcast is automatically configured based on the IP address
  • The name of the HTTP server (or its IP address and port) and the PHP script that receives JPEG images from the camera
  • Username and password to access the script and page on the server
  • The type of iNode that triggers the recording of images on the server and the time of registration or the period of images recording in online mode
  • The main password for encrypting JPEG images
  • The user's password for the embedded HTTP server
  • Administrator password for the embedded HTTP server

Power

• 5V Mini USB; 85mA @ 10Mbps; 130mA @ 100Mbps
• Or POE 6-30V DC; 40mA @ 100 Mbps 24V; 60mA @ 100 Mbps 12V; 120mA @ 100Mbps 6V

Housing

• metal
• Dimensions: 81 mm x 38 mm x 22 mm

Parameters of the CMOS 5MPx camera module

• Matrix 2560 x 1944
• F: 2.8
• Viewing angle: 70 °
• Lens type: ¼ inches with a fixed focal length
• Adjustable JPEG image resolutions:
  • 640 × 480
  • 1280 x 720
  • 1920 × 1080
  • 2592 × 1944
• Encryption of JPEG image content using the ARCFour / AES128 algorithm using a 128 bit key
• Transmission of JPEG images to the server via HTTP / POST - the number of frames up to 10 fps depends on the bandwidth of the link, set compression ratio, resolution set, etc.

others

• The possibility of remote exchange of software (via a web browser)
• Remote control via TCP / IP telnet on port 5500
• Two LEDs: ethernet LINK and STATUS
• HTTP server:
  • 6.9MB for HTTP (www) user sites and 1MB for HTTP (www) system websites
  • Support for a maximum of 2 connections at once
• One potential-free output: 60V 500 mA 2.5Ω (electronic relay); signals available on the USB connector
• 10Mbps / 100Mbps Ethernet RJ-45 connector, 10BaseT; protocols: ARP, SSDP, UDP, TCP / IP, DHCP, SNTP, HTTP, WEBSOCKET
• Reset button (restores factory settings)
• Temperature sensor with a resolution of 1 ° C
• Working temperature: -20 to 45 ° C
• Humidity: 35-80% RHG
• Weight: 65g

Software

• Any web browser with HTML5 support

The iNodeSetup.exe configuration software works only on Windows with a Bluetooth adapter based on the CSR 8510 chipset or iNode Serial USB Transceiver, iNode LAN.

Usage

• Control of the movement of persons and vehicles
• Monitoring of rooms and facilities
• Alarm systems and property protection

In our offer you will also find a 5V 1A miniUSB power supply suitable for this module.

To download

• Instructions for iNode LAN Camera
• The CSR 1011 chipset
• W5500
• OV5642
• Applications for ANDROID and WINDOWS
• Current firmware versions for iNode products are available on the support website: http://support.elsat.com.pl/
  User: Inode
  Password: missing