.png)
- Out-of-Stock
eMMC Module C1+/C0 Android Black - 32GB
ID: 561359
Pre-installed Android 4.x or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode
Description
eMMC Module C0/C1+ Android Black for ODROID-C0, ODROID-C1 and ODROID-C1+
Pre-installed Ubuntu 14.04 or latest version
eMMC Version 5.0 interface or higher version from Samsung. JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode.
Note! ODROID-C1 / C1+ / C0 host supports eMMC version 4.5
The eMMC chipset is only compatible with Amlogic S905 and S805 series (ODROID-C1+ / C0 / C2)
This eMMC chipset is NOT compatible with ODROID-XU4 / XU3 / U3 / U2 / X series
eMMC Module Reader is included
Adapter micro-SD for eMMC
eMMC attached to adapter
Storage I/O comparison
To obtain the results in the storage I/O comparison graph, type the following lines at a command prompt. The first command tests the write speed, and the second command tests the read speed:
$ dd if=/dev/zero of=test.tmp oflag=direct bs=500K count=1024
$ dd if=test.tmp of=/dev/null iflag=direct bs=500K count=1024
If you use the eMMC storage, you can get about two to three times faster storage I/O read performance. However, an affordable microSD UHS-1 card can still achieve reasonably fast speeds thanks to the advanced SD 3.01 host controller in the S805 processor. The MicroSD card read performance on C1+ is still about 1.7 times faster then RPi if you use the UHS-1 memory card.
561359
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Other products in the same category (16)
Module with 6 5x7 LED matrix displays designed to work with the Raspberry Pi. It uses IS31FL3730 drivers and communicates via the I2C interface. Pimoroni PIM187
Retired
No product available!
Module with 6 5x7 LED matrix displays designed to work with the Raspberry Pi. It uses IS31FL3730 drivers and communicates via the I2C interface. Pimoroni PIM187
Retired
No product available!
A module with 5 buttons and an RGB diode, designed to work with the Raspberry Pi. The buttons are connected to the minicomputer through the GPIO expander controlled by the I2C interface. Pimoroni PIM301
Retired
No product available!
Kit for controlling soil moisture of cultivated plants. It contains the HAT Mini module, soil moisture sensors and pots and seeds of herbs: basil, coriander and rosemary. Pimoroni PIM518
Retired
No product available!
Kit for controlling soil moisture of cultivated plants. It contains the HAT Mini module, soil moisture sensors and pots and seeds of chilli. Pimoroni PIM519
Retired
No product available!
A module with a spectrum sensor that operates in the visible light range (450-650 nm). It allows you to measure and characterize a light source or check how the tested surface absorbs or reflects light at specific wavelengths. Pimoroni PIM412
Retired
No product available!
Module with a UV ultraviolet light sensor VEML6075. It enables measurement of the level of UVA (350-375 nm) and UVB (315-340 nm) radiation. It communicates via the I2C bus. Pimoroni PIM460
Retired
No product available!
Module with 6-axis IMU motion sensor that combines a 3-axis accelerometer and a 3-axis magnetometer in one system. It communicates via the I2C bus. Pimoroni PIM376
Retired
No product available!
Module with two 5x7 LED matrix displays designed to work with the Raspberry Pi. It uses IS31FL3730 drivers and communicates via the I2C interface. Pimoroni PIM527
Retired
No product available!
Module with two 5x7 LED matrix displays designed to work with the Raspberry Pi. It uses IS31FL3730 drivers and communicates via the I2C interface. Pimoroni PIM526
Retired
No product available!
The system of a practical clock with an extremely simple design is equipped with a readable LED display, an alarm clock with a snooze function, and battery backup of the clock operation after a power failure
Retired
No product available!
Kit with DA7280 vibration motor driver module and LRA (Linear Resonant Actuator) motor. It allows you to add vibration feedback from the device to the project. SparkFun ROB-18247
Retired
No product available!
No product available!
The Winstar WEH001602ABPP5N00100 OLED display is a character display with dimensions of 80×36×10 mm, capable of displaying 16 characters on 2 lines. It comes with a built-in WS0010-TX controller and operates within a power supply voltage range of 4.8–5.3 V and temperature range of -40°C to 80°C, offering excellent readability thanks to OLED technology.
Retired
No product available!
Kit with Jetson Mate base board designed for SoM modules NVIDIA Jetson Nano and Jetson Xavier NX. It allows you to connect 4 SoM modules and create a home GPU computing cluster or server. Seeed Studio 110991411
Retired
No product available!
Jetson Mate motherboard for NVIDIA Jetson Nano and Jetson Xavier NX. It allows you to connect 4 SoM modules and create a home GPU computing cluster or server. Seeed Studio 114992562
Retired
No product available!
Pre-installed Android 4.x or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode