- Out-of-Stock

Blynk is an easy to use app builder that allows users to add a variety of buttons, sliders, graphical displays and even RGB controllers to their phone. The SparkFun Blynk Board is specially designed to work with the ‘widgets’ within the Blynk mobile app to create your next IoT project. Monitor local weather conditions, control LEDs from your phone, even send a tweet when it’s time to water your plants!
The SparkFun IoT Starter Kit with Blynk Board is a great way to gain a solid introduction to the world of Internet of Things (IoT) technology without any difficult programming. With this kit you will be able to get your Blynk Board connected and, by utilizing the pre-loaded projects, use diverse set of components to build an array of web- and phone-connected projects.
Every Blynk Board comes fully programmed and also includes a Blynk subscription code card (15k Energy at a $10 value), which will be needed to connect the Blynk Board to your Blynk account. Simply connect to a Wi-Fi signal and you are ready to use this starter kit! Getting started with your Blynk Board and getting it connected to the Blynk App on your iOS or Android device is a breeze.
The kit does not require any soldering and is recommended for anyone with a drive to learn more about Blynk and its uses. So if you are looking for a new challenge or a way to get in on the IoT craze, check out the SparkFun IoT Starter Kit with Blynk Board!
Note: The Blynk app is compatible with iDevices running iOS 7.0+, and Android’s running any version above or equal to 4.0.
Note: Customers who initially order this Starter Kit may receive a white USB wall wart instead of the one listed below and seen in the image above. The included wall wart will be capable of 5V and 1A regardless of what it looks like.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The module allows measuring the light around the sensor. The measuring range is in the range 1 - 65535 LUX, and communication takes place using the I2C bus. modBH1750 (GY-302)
IoT development board the size of Arduino, equipped with an ARM Cortex-M3 processor (STM32F205) and a Wi-Fi communication module (with an integrated antenna and uFL connector). SparkFun DEV-13321
SensorTag is 10 sensors in a small housing with the ability to transfer readings via Bluetooth to a tablet or mobile phone and to put data in the cloud. CC2650STK
No product available!
SDR (Software Defined Radio) receiver that allows you to receive signals in the frequency range from 10 kHz to 1 GHz. It is ideal for both monitoring low frequencies and receiving signals on higher bands
No product available!
No product available!
Permanent cylindrical neodymium magnet with a diameter of 18 mm and a height of 2 mm.
No product available!
eMMC Flash memory module for Hardkernel Odroid N2L computers. 64GB capacity, installed Android operating system. The set includes a microSD adapter. Hardkernel 64GB eMMC Module N2L Android
No product available!
No product available!
No product available!
Easy-to-use and intuitive 3D printer with a touch display and support for USB, WiFi and cloud file transfer. The printer is fully assembled and ready to use. Flashforge Adventurer 4
No product available!
Breadboard-friendly development board with 32 bit ARM Cortex-M4. Adafruit 2756, DEV-13736
No product available!
Programmable watch with ESP32-Pico-D4. Equipped with a touch button display, motion sensor, power management system, RTC clock and Lithium battery. LILYGO TTGO T-Wristband
No product available!
No product available!
MICRO SD module, connected with pin connectors, supply voltage 3.3V, RoHS
No product available!
No product available!
No product available!
No product available!
The Cloudshell for XU4 is an affordable DIY Network Attached Storage (NAS) Solution to create your own personal cloud! It includes a color LCD console display on the front and has room for a 2.5inch HDD/SSD along with the XU4 board inside the CloudShell
No product available!
The Raspberry Pi GPIO connector adapter allows you to output signals from Raspberry Pi to the contact plate. Two LEDs indicate +3.3V and +5V power supply
No product available!
KIT-13865