- Out-of-Stock
AVT5540 B - radio for everyone. Self-assembly set
ID: 561941
AVT kit for self-assembly of the radio. AVT5540 B
Description
The receiver was made using popular and easy to assemble elements, so its implementation will not cause any difficulties even for beginners.
The role of the radio tuner is fulfilled here by the module with the RDA5807 system. Includes a radio chip, a quartz resonator and several passive components. After assembly, it is only necessary to set the contrast of the display with the potentiometer R1. After this, he is ready to work.
Project AVT 5540 EP 05/16
properties
- Easy assembly and commissioning
- It does not require tuning
- It uses a module with the RDA5807 radio system
- Stereo output - 2 channels with 2W each
- The possibility of cooperation with headphones or a set of speakers
- Reception of radio stations in the range of 87.5 ... 108 MHz
- Receipt and display of RDS information
- Memory of 8 radio stations
- Power supply: 7 ... 15 V DC / 0.3A
- Small dimensions: 140 × 38 × 45mm
Included
- Kit for self-assembly of the radio
Attention! Speakers are not included. You should get them yourself.
561941
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
No product available!
No product available!
The miniature digital potentiometer allows you to replace the analog potentiometer and control the resistance value using two buttons. The module contains inputs of the UP / DOWN buttons (for increasing and decreasing the resistance) and outputs in accordance with the analog potentiometer A, W, B (description on the circuit board). MOD-19.Z
Retired
No product available!
Xmega eXploreGO module with ATXmega128A4U microcontroller (version without MP3). The module is equipped with in DataFlash memory, microSD card connector. MOD-20 / AZ
Retired
No product available!
MOD-21.Z - push button module with bistable operation. The sensor operates based on the AT42QT1012 system.
Retired
No product available!
The Raspberry Pi GPIO connector adapter allows you to output signals from Raspberry Pi to the contact plate. Two LEDs indicate +3.3V and +5V power supply
Retired
No product available!
No product available!
MOD-25.Z - touch sensitive button module with monostable function. The sensor operates based on the AT42QT1011 system.
Retired
No product available!
No product available!
No product available!
The module enables connection of two devices with I2C interface working with different voltage levels. MOD-28.Z
Retired
No product available!
It is used to monitor the temperature measurement and other parameters. The expansion module has an I2C / 1-Wire converter (DS2482) through which DS18B20 temperature sensors can be connected using two or three wires. MOD-29.Z
Retired
No product available!
Power module with IRFR4105Z transistor (MOD-30.Z), maximum current 2A, 5V power supply or 5V - 12V range (selection by jumper)
Retired
No product available!
The module with the DS18B20 sensor is used to measure the temperature in the range from -55° C to + 125° C, with an accuracy of +/- 0.5° C in the range from -10° C to + 85° C. The module communicates via the 1-Wire interface, thanks to which it can be connected using 2 or 3 wires - depending on the configuration. Temperature measurement can be performed with an accuracy of 9 to 12 bits. MOD-31.Z
Retired
No product available!
Universal module with LM358 operational amplifier. Depending on the additional elements installed, the amplifier can be freely configured, eg as a reversing, non-inverting amplifier, voltage follower or an integrating amplifier. MOD-32.Z
Retired
No product available!
No product available!
AVT kit for self-assembly of the radio. AVT5540 B