- Out-of-Stock
MyoWare Muscle Sensor Development Kit
ID: 562373
Arduino-powered, electromyography (EMG) sensor kit that provides you with a MyoWare Muscle Sensor, each shield developed here at SparkFun, and everything you need to connect them all together. KIT-13772
Description
Using our muscles to control things is the way that most of us are accustomed to doing it. We push buttons, pull levers, move joysticks … but what if we could take the buttons, levers and joysticks out of the equation? This is the MyoWare Muscle Sensor Development Kit, an Arduino-powered, electromyography (EMG) sensor kit that provides you with a MyoWare Muscle Sensor, each shield developed here at SparkFun, and everything you need to connect them all together.
The MyoWare board, included in this kit, acts by measuring the filtered and rectified electrical activity of a muscle; outputting 0-Vs Volts depending on the amount of activity in the selected muscle, where Vs signifies the voltage of the power source. It’s very simple to hook up this kit, attach shields to the muscle sensor, stick on a few included electrodes, read the voltage out and flex some muscles!
Also included in this kit is everything you need to set up the MyoWare Muscle Sensor: all associated shields (Power, Cable, LED, and Proto), biomedical sensor pads and cable, as well as headers that can be soldered onto each shield so they can be attached together. Make sure to take a look at our MyoWare Muscle Sensor Kit Guide below for tips, tricks and best practices for assembling your MyoWare boards.
To make stacking easier, the MyoWare Muscle Sensor Development Kit includes 3-pin stackable headers. Using these on all of the shields allows for easy stacking in more configurations.
Note: The Power Shield and the LED Shield both provide power, but at slightly different voltages. Don’t use both of these shields at the same time.
Note: This item may take longer to process due to battery installed in the equipment and therefore does not qualify for same-day shipping policy. Additionally, these batteries can not be shipped via Ground or Economy methods to Alaska or Hawaii. Sorry for any inconvenience this may cause.
Features
Includes:
- 1x MyoWare Muscle Sensor
- 1x MyoWare Power Shield
- 1x MyoWare Cable Shield
- 1x MyoWare LED Shield
- 1x MyoWare Proto Shield
- 1x Sensor Cable - 3 Connector
- 10x Biomedical Sensor Pad
- 11x Stackable Header - 3 Pin, Female
- 3x Header - 3 Pin, Male
562373
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
The MyoWare Power Shield is designed to take two standard CR2032 coin cell batteries to power the MyoWare Muscle Sensor. We have made this board in a way that the coin cell batteries are connected in parallel for extended capacity at a nominal 3.0V. DEV-13684
zł37.71
Delivery date unknown
No product available!
Designed to pair with the MyoWare Muscle Sensor; 10-segment bar graph shows the magnitude of the measured signal. The more muscle activation measured, the higher up the board the lit LEDs will go. DEV-13688
Regular pricezł101.73zł23.90
24h
Available quantity: 11
Available
Other products in the same category (16)
FPGA starter kit with Intel Stratix 10 GX. The module has integrated transceivers that transfer data at speeds up to 28.3 Gb/s, making DE10-Pro fully compatible with version 3.0 of the PCI Express standard. The DE10-Pro offers fast parallel Flash memory and four SO-DIMM slots that support DDR4 SDRAM options. Terasic P0626
Retired
No product available!
No product available!
No product available!
LCD 2x20, 146x43mm, LED backlight (WHITE) NEGATIVE BLUE, enhanced temperature range, 9.22mm character
Retired
No product available!
No product available!
HAT for powering over Ethernet (PoE) for Raspberry Pi. It allows you to use the PoE interface to power the minicomputer via an Ethernet cable
Retired
No product available!
No product available!
No product available!
Module with a driver designed for small DC motors. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020084
Retired
No product available!
No product available!
No product available!
No product available!
No product available!
NOR08 is a workshop organizer made of high quality plastic, with a transparent cover, closed with latches, with a solid handle for convenient transport. It has the ability to regulate the size and number of compartments
Retired
No product available!
Modern Ukraine has a beautiful legend about a heroic ace pilot who defended the skies over Kyiv in his MiG-29 fighter. During the first 30 hours of the full-scale invasion of russia, "The Ghost of Kyiv" shot down six hostile russian aircraft, taking his place in the history of Ukraine forever. In total, he was credited with at least 40 kills. People called this unknown hero "The Ghost of Kyiv." It is impossible to overcome him, it is impossible not to admire him. In fact, the "Ghost of Kyiv" is a composite character of the pilots of the 40th Tactical Air Force Brigade of Ukraine, which has bravely defended Ukrainian skies ever since russia launched its war of aggression. UGears 70191
Retired
No product available!
No product available!
Arduino-powered, electromyography (EMG) sensor kit that provides you with a MyoWare Muscle Sensor, each shield developed here at SparkFun, and everything you need to connect them all together. KIT-13772