- Out-of-Stock
DCF77 signal receiver (MAS6180) with a ferrite antenna
ID: 562522
The AM receiver of the DCF77 signal with the MAS6180 system, allows to receive the frames of the synchronization signal from the time standard, using the carrier frequency of 77.5kHz. Thanks to this module, it is possible to create a clock with automatic date and time synchronization. The module has a ferrite antenna. modDCF77
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
The AM receiver of the DCF77 signal with the MAS6180 system, allows to receive the frames of the synchronization signal from the time standard, using the carrier frequency of 77.5kHz. Thanks to this module, it is possible to create a clock with automatic date and time synchronization. The module has a ferrite antenna.
properties
- DCF77 signal receiver with MAS6180B5 system
- It allows you to synchronize clocks with the cesium time pattern
- Power supply: 1.1V - 3.6V
- Signals led out to soldering pads (6 pads)
- Description of pins:
- V - positive supply pole
- G - negative power pole
- TN - DCF77 signal output
- AO - positive supply pole
- PO - sleep mode (high state) or work (low state)
- F - not used
- Module dimensions: 26mm x 14mm x 3mm
Included
- Receiver module DCF77 with a ferrite antenna
562522
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
No product available!
No product available!
- Michael Gregg, Eric Seagren, Angela Orebaugh, Matt Jonkman, Raffael Marty Delivery date unknown
No product available!
The controller allows you to easily control the work of any device with the SPI interface via the USB port. All you need is a FTDI USB driver . TOL-09235
Retired No product available!
Kit containing Raspberry Pi Pico and Raspberry Pi 4B 4 GB. The kit also includes the necessary connectors, cables, power supply and housing - heat sink
Retired No product available!
No product available!
AA/LR6/R6 alkaline battery with 1.5V voltage, 4 pcs.
Retired No product available!
USB A 2.0 / USB C cable silicone, 1 m, black
Retired No product available!
No product available!
No product available!
LPC55S69JEV98K, ARM Cortex-M33 Microcontroller, 32 bit, 150 MHz, 640 KB Flash, VFBGA98
Retired No product available!
No product available!
No product available!
- Eric Le Ru, Pablo Etchegoin Delivery date unknown
No product available!
The Curvimeter – or opisometer – is a device that measures the length of curved lines and helps to calculate the distance between the points on a map more precisely than a ruler or a compass.
The mechanism has a measuring wheel, a clock face, and a hand. When the wheel moves along the line on a map that you need to measure, the hand moves around the clock face marked with measuring units – centimeters, inches, etc. All you need to do in the end is to check the map scale and to multiply your data by the denominator in the scale. UGears 70138
Retired No product available!
Infrared sensor that allows measurement of distances up to 15cm, has a built-in infrared illuminator, IR receiver and a perimeter of the received signal
Retired No product available!
The AM receiver of the DCF77 signal with the MAS6180 system, allows to receive the frames of the synchronization signal from the time standard, using the carrier frequency of 77.5kHz. Thanks to this module, it is possible to create a clock with automatic date and time synchronization. The module has a ferrite antenna. modDCF77