.png)
- Out-of-Stock
Driver of model servos
ID: 557577
MOD-17.Z
Model servo driver, 2-channel
Description
The controller allows independent control of two modeling servos by means of buttons or 1/0 signals. The outputs match the servo signals (SYG, + V, GND), so there is no need for additional wires or adapters.
Important: The controller has been designed for Redox S90 and Tower Pro SG90 servos.
The jumper allows you to power the servos from the same or a separate power source.
Each time the SW3 button is pressed (for the second servo - SW2), the servo axis will be rotated by about 180 degrees. Pressing the SW1 button will rotate both servos 90 degrees, which means they are in the middle position. It is also possible to control from the S1-S3 inputs corresponding to the buttons. The inputs are activated by a low state, which is equivalent to pressing a given button.
Technical data:
- Code and name of the MOD-17 module. 2-channel model servo controller
- Integrated circuit: ATtiny13
- Input connector: S1-S3 to control the servos, corresponding to pressing the button
- Description of the input connector: GND, + 5V, S1, S2, S3
- Outputs / output connector: SM1 and SM2 for 2 servos
- Power supply: +2.7 V to +5.0 V
- LED signaling: yes
- Configuration: power selection connector
- Dimensions: 31 mm x 25 mm
- Additional information:
- the possibility of mounting angle buttons
- power filtering capacitors
- the jumper allows the servos to be powered from the same or a separate power source
- RoHS: yes
Set contains:
- assembled MOD-17.Z 2-channel model servo controller
- set of connectors for self-assembly (11-pin 1 pcs)
To download
557577
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Other products in the same category (16)
No product available!
Translator of TI voltage levels, bidirectional (no signal required to control the flow direction), 8-Bit, especially recommended for use in Push-Pull and Open-Drain systems. The system has a TSSOP20 housing
Retired
No product available!
Aluminum extensometer beam, allowing measurement of weight up to 1 kilogram. It has four wires. It is used in kitchen scales and portable scales.
Retired
No product available!
Aluminum extensometer beam, allowing weight measurement up to 3 kilograms. It has four wires. It is used in kitchen scales and portable scales.
Retired
No product available!
Aluminum extensometer beam, allowing mass measurement up to 5 kilograms. It has four wires. It is used in kitchen scales and portable scales.
Retired
No product available!
A two-wire, serial extender for I2C bus, SMBus and HDMI DDC, working at 2.7 V - 5.5 V. The system has a TSSOP8 housing. PCA9507DP
Retired
No product available!
32-bit microcontroller from the STM32F7 family with ARM Cortex-M7 core, 512kB Flash memory, 320kB SRAM, I2C, SPI, UART / USART memory, USB, CAN, 1.71 ... 3.6V, 100LQFP, STM, RoHS
Retired
No product available!
The 32-bit microcontroller from the STM32F7 family with the ARM Cortex-M7 core, has 1024 kB Flash memory and 320kB SRAM memory. Supports LCD-TFT, USB OTG HS, Ethernet, CAN, UART, I2C, SPI, ADC, DAC. System in the 144-LQFP housing. STM32F746ZGT6
Retired
No product available!
The set allows introducing distance, ambient lighting and gesture analysis into the subject using the VL6180X sensor. NUCLEO-L053R8 plate in set with VL6180X expansion board. P-NUCLEO-6180X2
Retired
No product available!
Shield for STM32 Nucleo, has two MP34DT01-M digital microphones made in MEMS technology
Retired
No product available!
9-inch display with universal HDMI interface and 10-point multitouch capacitive screen
Retired
No product available!
Load Cell Amplifier is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. SEN-13230
Retired
No product available!
Shadow Chassis is a marvelously durable and modular robot platform from RobotZone. The chassis plates and mounts are cut from ABS plastic and utilize the Actobotics 0.77" and 1.50" hub patterns for sensors, controllers, power, etc. With the included “snap on” micro-controller mounts, you can attach an Arduino, Raspberry Pi, SparkFun RedBoard, or SparkFun RedBot Mainboard!
Retired
No product available!
Bluetooth module for mounting in SMD technology with a fully configurable UART interface - transfer speed up to 2 Mb / s. WRL-11786
ATTENTION! A newer version of this product is available.
Click to go to the product page
Retired
No product available!
The LCD Button Shield V2 attaches to your Arduino to provide a 16x2, black character, green back light LCD with a keypad consisting of 5 keys — select, up, right, down and left. With this shield you will be able to move through menus and make selections straight from one board attached to your Arduino without requiring a massive tower of shields. DEV-13293
Retired
No product available!
No product available!
MOD-17.Z