- Out-of-Stock
AVT5565 B - DC motor driver for the drive. Self-assembly set
ID: 563202
AVT kit for self-assembly of the DC motor driver for the drive. AVT5565 B
Description
The AVT5565 is used to control the DC motor and allows it to operate in both directions of rotation at a controlled speed. The controller is equipped with a soft start function, with stop by means of limit switches, after a specified time or in the event of an overload.
The controller can be used, for example, as a gate drive controller, blinds and others.
Project AVT 5565 EP 10/16
properties
- Operation with DC motors supplied with 3 ... 48 V DC, maximum 15 A
- Regulation of the direction and speed of the engine
- Soft start function
- Automatic stop triggered by a signal from the limit switches
- Optional time-out function with time adjustment from 2 seconds to 2 minutes
- Optional overload shutdown function
- Controller supply 12 ... 30 V DC / 0.2 A
- Dimensions 84 × 50 × 30 mm (without radiator)
Included
- A set of parts for self-assembly of the controller
563202
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
A module with a color and gesture sensor based on the APDS-9960 chip. It can detect simple hand gestures, RGB colors and measure ambient light. DFRobot SEN0187
Retired
No product available!
Power Supply 2.5A 5.1V for Raspberry Pi 3 model B - STONTRONICS T5875DV
Retired
No product available!
Pre-installed Ubuntu 14.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode
Retired
No product available!
No product available!
No product available!
Pre-installed Ubuntu 14.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode
Retired
No product available!
Pre-installed Android 4.x or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode
Retired
No product available!
3.2D soldering tip, flat screwdriver 5.5mm in diameter, for WEP 926 soldering station
Retired
No product available!
Pre-installed Ubuntu 14.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode
Retired
No product available!
5V / 3.1A eXtreme power supply with microUSB plug for all Raspberry Pi computers (including Pi 3 model B and Pi 3 model B +)
Retired
No product available!
Antenna with built-in LNA amplifier with high sensitivity, for mounting in a device using a GPS module. The antenna has a 25mm cable, terminated with a U.FL plug (IPEX). Dimensions of the device: 9 x 9 x 4mm
Retired
No product available!
The GY-GPS6MV1 module is a board containing the U-blox NEO-6M GPS receiver system. The tile also includes RTC backup battery, antenna connector (U.FL), voltage stabilizer and UART signal outputs
Retired
No product available!
Kit: MAXimator, MAXimator Expander, ZL32PRG - USB Blaster PRO
Retired
No product available!
Power Supply 2.5A 5.1V for Raspberry Pi 3 model B - STONTRONICS T5875DV
Retired
No product available!
MYD-JA5D44 Development Board is a complete educational platform. Its heart is the MYIR MYC-JA5D44 module, which was equipped with the Atmel SAMA5D44 processor based on Cortex-A5 cores. The processor can work at a maximum frequency of 600 MHz. Min. RS232, RS485 connectors, HDMI connector, 3.5 mm Jack Audio inputs, microSD memory card slot, 10/100 Mbps Ethernet slot and many more.
Retired
No product available!
The Raspberry Pi GPIO Triple Expansion Board converts the single GPIO headers on your Raspberry Pi into three parts. DFR0385
Retired
No product available!
AVT kit for self-assembly of the DC motor driver for the drive. AVT5565 B