- Out-of-Stock

The beam allows you to measure weight up to 20 kilograms. It has four wires. Aluminum strainer beam, mounted on screws (not included), screwed in with threaded holes. Cable length 21 cm.
The importance of wire colors:
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Aluminum extensometer beam, allowing measurement of weight up to 1 kilogram. It has four wires. It is used in kitchen scales and portable scales.
No product available!
Aluminum extensometer beam, allowing measurement of weight up to 20 kilograms. It has four wires. It is used in kitchen scales and portable scales, it has a 21 cm cable, RoHS.
No product available!
Aluminum extensometer beam, allowing weight measurement up to 100 kilograms. It has four wires. It is used in kitchen scales and portable scales, max 100 kg, 20x23x94, 21 cm cable, RoHS
No product available!
The module allows you to attach a strain gauge (working in the Wheatstone bridge circuit) and convert the analog signal into its digital representation, available on the module output lines. The system processes the signal with a 24-bit resolution and can be powered by 2.7V - 5.5V. The module is especially recommended for constructing digital scales in combination with Arduino
A module with a 24-bit ADC converter HX711, which allows you to read data from strain gauges and scales. It communicates via the serial interface. SparkFun SEN-13879
No product available!
Simple-to-use, open source solution for measuring weight and temperature with the ability to read multiple types of load cells and offers a simple-to-use serial menu to configure calibration value, sample rate, time stamp and units of precision. SEN-13261
No product available!
NUN14 is a workshop organizer made of high quality plastic, transparent, closed with latches, with a solid handle for convenient transport. It has 5 chambers
No product available!
Powerful Polol 3pi robot work. Line Follower mobile platform with two motors, 5 reflection sensors, LCD display, buzzer and three user buttons as well as mbed extension board with NXP LPC1768 module. Pololu 2153
No product available!
No product available!
KAmodRPI RS485 CAN HAT is a shield for the Raspberry Pi computer that extends its interfaces with RS485 and CAN. Bus signals are led out to goldpin connectors and terminal blocks.
No product available!
Camera module with USB interface with 2MP resolution. Camera with Sony CMOS IMX323 sensor, the module is equipped with two microphones. ArduCAM UB0212
No product available!
Micro SD 8GB class 4 card with Linux Raspbian Wheezy for RPi
No product available!
CO2 sensor module with MG811 system with a voltage of 6 V. The module has an analogue output of 30 ... 50mV and TTL
No product available!
No product available!
Kit containing Raspberry Pi Pico and Raspberry Pi 4B 4 GB. The kit also includes the necessary connectors, cables, power supply and housing - heat sink
No product available!
No product available!
No product available!
Development kit with STM32F401VCT6 microcontroller (256 kB Flash, 64 kB RAM, LQFP100 housing) and a built-in programmer / debugger ST-Link v. 2. Additional equipment are: a gyroscope (L3GD20), an accelerometer with a magnetometer (LSM303DLHC), a microphone (MP45DT02) and D / A converter with amplifier (CS43L22).
No product available!
The Digilent Cmod A7 is a small, breadboard friendly 48-pin DIP form factor board built around a Xilinx Artix-7 FPGA. The board also includes a USB-JTAG programming circuit, USB-UART bridge, clock source, Pmod host connector, SRAM, Quad-SPI Flash, and basic I/O devices. 410-328
No product available!
PCB with programmed system for slow brightener for 12V LED strips. AVT1975 A +
No product available!
HK Hobbyking 2~6S Lipo to USB Charging Adapter and Cell Checker (22320)
No product available!
Aluminum extensometer beam, allowing measurement of weight up to 20 kilograms. It has four wires. It is used in kitchen scales and portable scales, max. 20 kg, dimensions: 80x7x7 mm, has a 21 cm cable. Tensom20kg02