- Out-of-Stock
zł10,639.61
.png)
New products
New products New products
Filament ROSA3D PLA Starter 1.75mm Neon Orange
ID: 587765
5907753130785
ROSA3D filament made of high-quality PLA granules. 0.8 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PLA Starter Neon Orange
Description
1.75 mm PLA filament for 3D printing by ROSA3D. 0.8 kg of filament is wound on the spool. The recommended printing temperature is in the range from 185°C to 225°C, and the bed temperature during printing in the range of 40°C - 60°C, however, when using adhesives, heating the bed is not necessary.
Rosa3D is a Polish manufacturer of filaments intended for both hobby and industrial printing. Thanks to many years of experience and modern machinery, the company is able to provide good quality and accuracy of the diameter and roundness of the filament. Filament PLA Starter from Rosa3D was designed for beginner users of 3D printers. The simplicity of PLA Starter printing will allow you to enjoy aesthetic prints, and over time will convince you to print more and more complex and demanding projects.
PLA is the basic material used in 3D printing. PLA Starter is characterized by low shrinkage and no unpleasant odor. The prints are characterized by excellent layer adhesion and very good detail reproduction. The filament is made of a biodegradable biopolymer. It was made of ingredients approved for contact with food.
Features
- Color: Neon Orange
- Diameter: 1.75 mm
- Diameter tolerance: +/- 0.05mm
- Oval tolerance: +/- 0.02 mm
- Printing temperature: 185°C to 225°C
- Bed temperature: 40°C to 60°C (when using washers or other means to increase the adhesion heating of the table is not required)
- Density 1.24 g/cm3
- Odorless smell
- Elongation at tensile 6%
- Tensile strength (to break) 53 MPa
- Modulus of elasticity at tensile 3500 MPa
- Heat deformation temperature 55°C
- Net weight: 0.8 kg
587765
Data sheet
- Rodzaj filamentu
- PLA
- Ilość filamentu
- 0,8 kg
- Diameter
- 1,75 mm
- Colour
- Pomarańczowy
You might also like
Knife designed for trimming and processing of prints from a 3D printer. It consists of a plastic handle and a replaceable, curved blade made of steel
zł9.02
24h
Available quantity: 82
Available
Adhesive increasing the adhesion of 3D prints to the glass table. It makes it easier to work with all materials and prevents undesirable curling of the elements. Dimafix Spray 400ml
zł56.14
24h
Available quantity: 23
Available
Adhesive increasing the adhesion of 3D prints to the glass table. It makes it easier to work with all materials and prevents undesirable curling of the elements. Dimafix Pen 90ml
zł49.48
24h
Available quantity: 154
Available
Other products in the same category (16)
The 32-bit microcontroller from the STM32F7 family with the ARM Cortex-M7 core, has 1024 kB Flash memory and 320kB SRAM memory. Supports LCD-TFT, USB OTG HS, Ethernet, CAN, UART, I2C, SPI, ADC, DAC. System in the 144-LQFP housing. STM32F746ZGT6
Retired
No product available!
The set allows introducing distance, ambient lighting and gesture analysis into the subject using the VL6180X sensor. NUCLEO-L053R8 plate in set with VL6180X expansion board. P-NUCLEO-6180X2
Retired
No product available!
Shield for STM32 Nucleo, has two MP34DT01-M digital microphones made in MEMS technology
Retired
No product available!
9-inch display with universal HDMI interface and 10-point multitouch capacitive screen
Retired
No product available!
Load Cell Amplifier is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. SEN-13230
Retired
No product available!
Shadow Chassis is a marvelously durable and modular robot platform from RobotZone. The chassis plates and mounts are cut from ABS plastic and utilize the Actobotics 0.77" and 1.50" hub patterns for sensors, controllers, power, etc. With the included “snap on” micro-controller mounts, you can attach an Arduino, Raspberry Pi, SparkFun RedBoard, or SparkFun RedBot Mainboard!
Retired
No product available!
Bluetooth module for mounting in SMD technology with a fully configurable UART interface - transfer speed up to 2 Mb / s. WRL-11786
ATTENTION! A newer version of this product is available.
Click to go to the product page
Retired
No product available!
The LCD Button Shield V2 attaches to your Arduino to provide a 16x2, black character, green back light LCD with a keypad consisting of 5 keys — select, up, right, down and left. With this shield you will be able to move through menus and make selections straight from one board attached to your Arduino without requiring a massive tower of shields. DEV-13293
Retired
No product available!
No product available!
Nintendo DS Screen Kit joins two of our more unique products together to provide you with an easy means to equip your next project with touchscreen functionality. Inside each kit is one Nintendo DS Touchscreen and one SparkFun Touchscreen Connector Breakout. LCD-13631
Retired
No product available!
MG2639 SparkFun Cellular Shield is a perfect addition to any Arduino project that requires connectivity when there’s no WiFi or Ethernet access nearby. The ZTE MG2639 module, which this shield is built around, supports SMS, TCP, UDP, and can even be used to make or receive phone calls. CEL-13120)
Retired
No product available!
Imagine an Arduino Shield that can be configred to be an LCD, GPS, Wuifi, or any shield you may think of!
Delivery date unknown
No product available!
Module with analogue UV light sensor ML8511. It enables the measurement of the radiation intensity for the UV-A (320-400nm) and UV-B (280-320nm) waves. Analog interface. DFRobot SEN0175
Retired
No product available!
What you need is an add on prototyping T-breakout board, which can break out all those tasty power, GPIO, I2C, ADC pins from the 40 pin header onto a solderless breadboard. This set will make "cobbling together" prototypes with the ODROID-C1 super easy
Retired
No product available!
Development Boards & Kits - ARM SAMD10 Xplained Mini evaluation kit, Microchip
Retired
No product available!
Module cooperating with Arduino Ethernet Shield 2 and Arduino Ethernet. It allows you to connect power to Arduino from an Ethernet network. Compliant with the IEEE 802.3af Power-over-Ethernet standard.
Retired
No product available!
ROSA3D filament made of high-quality PLA granules. 0.8 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PLA Starter Neon Orange