- Out-of-Stock
Filament ROSA3D ASA 1.75mm Natural
ID: 587786
5907753130532
ROSA3D filament made of high-quality ASA polymer. 0.7 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D ASA Natural
Description
ASA filament (acrylonitrile-styrene-acrylic) for 3D printing with a diameter of 1.75 mm by ROSA3D. 0.7 kg of filament is wound on the spool. The recommended printing temperature is in the range of 220°C to 250°C, and the temperature of the bed during printing is in the range of 90°C to 110°C. The manufacturer recommends printing in a closed chamber.
Rosa3D is a Polish manufacturer of filaments intended for both hobby and industrial printing. Thanks to many years of experience and modern machinery, the company is able to provide good quality and accuracy of the diameter and roundness of the filament. ASA filament from Rosa3D is resistant to UV radiation, moisture and heat. It will find applications in the automotive, marine and outdoor industries such as mirror housings, covers, radiator covers and sensor housings.
ASA filament is a suitable material for outdoor applications that will be intensely exposed to the sun and various weather conditions. It is ideal when the user needs an efficient material that will be less problematic than printing from ABS. The filament has less shrinkage and the vapors produced are much less noticeable. The softening point of ASA prints is higher compared to PLA and PET-G, there are no signs of deformation up to the temperature of about 94°C.
Features
- Color: Natural
- Diameter: 1.75 mm
- Diameter tolerance: +/- 0.05mm
- Oval tolerance: +/- 0.02mm
- Printing temperature: 220°C to 250°C
- Bed temperature: 90°C to 110°C
- It is recommended to print in a closed chamber
- Density 1.07 g/cm3
- Odor: almost odorless
- Elongation at tensile 35%
- Tensile strength (to break) 40 MPa
- Tensile modulus 1750 MPa
- Impact strength according to the Izod method with a notch 45 kg*cm/cm
- Heat deformation temperature 94°C
- Net weight: 0.7 kg
587786
Data sheet
- Rodzaj filamentu
- ASA
- Ilość filamentu
- 0,7 kg
- Diameter
- 1,75 mm
- Colour
- White
You might also like
3D printer with dual color print and heated table. The printer is fully assembled and ready to use. Flashforge Creator PRO
Regular pricezł4,365.91zł3,199.00
24h
Available quantity: 1
Available
Knife designed for trimming and processing of prints from a 3D printer. It consists of a plastic handle and a replaceable, curved blade made of steel
zł9.40
Delivery date unknown
No product available!
Adhesive increasing the adhesion of 3D prints to the glass table. It makes it easier to work with all materials and prevents undesirable curling of the elements. Dimafix Spray 400ml
zł52.90
24h
Available quantity: 87
Available
Adhesive increasing the adhesion of 3D prints to the glass table. It makes it easier to work with all materials and prevents undesirable curling of the elements. Dimafix Pen 90ml
zł54.46
24h
Available quantity: 266
Available
3D printer with two extruder and a heated table. It is fully assembled and ready to use. Flashforge Creator Pro 2
Regular pricezł5,292.28zł3,999.00
24h
Available quantity: 1
Available
Other products in the same category (16)
CryptoShield is a dedicated security peripheral for the Arduino. This shield adds specialized ICs that perform various cryptographic operations which will allow you to add a hardware security layer to your Arduino project. It also is a nice device for those performing embedded security research. DEV-13183
Retired
No product available!
No product available!
Banana Pi R1 acrylic clear case. The case needs to be assembled by yourself
Retired
No product available!
The housing for the Banner PI G1 Debugger made of transparent plastic. Housing for self-assembly
Retired
No product available!
The I2C electric level conversion module is specifically designed for Banana Pi. The module converts the 3.3V of I2C electric level to 5V level or converts 5V to 3.3V
Retired
No product available!
BPI AD/DA extend module with the PCF8591 single-chip, single-supply low-power 8-bit CMOS data acquisition device with four analog inputs, one analog output and a serial I2C-bus interface
Retired
No product available!
No product available!
5dB antenna for the Banana Pi R1 router in the version with 300Mps wifi and five LAN 100/1000 ports.
Retired
No product available!
STM32F103 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
CC3200 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
CC2530 and CC2540 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
It is a standard audio-video cable, which can be successfully used to connect Banana Pi M1 or Raspberry Pi 1 model B and A. Cable length is 98 cm, has two ends of the chinch type.
Retired
No product available!
COM-11964 Button a white economy grade 100mm diameter (outside diameter) dome illuminated push button comes with an LED, securing nut and a long life horizontal microswitch.
Retired
No product available!
Cobbler Plus - adapter enabling connection of GPIO Raspberry Pi A +, B + and Pi 2 lines to the contact plate (2.54 mm). The version is assembled. Adafruit 2029
Retired
No product available!
T-Cobbler Plus - adapter enabling connection of GPIO Raspberry Pi A +, B + and Pi 2 lines to the contact plate (2.54 mm). Goldpin connectors are included, for self-assembly. Adafruit 1989
Retired
No product available!
FPC tape length 250 mm, 50 lines, pitch 0.5 mm. Adafruit 1682
Retired
No product available!
ROSA3D filament made of high-quality ASA polymer. 0.7 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D ASA Natural