Category: RETIRED PRODUCTS

Motion sensor module dedicated to home automation systems. It allows monitoring of ambient heat (infrared band) and ambient light intensity and generates events when a sudden change is detected. Adaprox LKMSZ011

Two-channel switch with WiFi that can control two circuits in a room. Allows each of the two channels to be switched on/off independently. Adaprox LKWSW201

Insulated fibre-optic probe with a measurement range of up to 2500 V. Operates in a bandwidth of up to 100 MHz and can be connected to an oscilloscope via a BNC connector. Battery-powered. Micsig OIP100B

Insulated fibre-optic probe with a measurement range of up to 2500 V. Operates in a bandwidth of up to 200 MHz and can be connected to an oscilloscope via a BNC connector. Battery-powered. Micsig OIP200B

Insulated fibre-optic probe with a measurement range of up to 2500 V. Operates up to 350 MHz and can be connected to an oscilloscope via a BNC connector. Battery-powered. Micsig OIP350B

Insulated fibre-optic probe with a measurement range of up to 1250 V. Operates in a bandwidth of up to 500 MHz and can be connected to an oscilloscope via a BNC connector. Battery-powered. Micsig OIP500B

Insulated fibre-optic probe with a measurement range of up to 1000 V. Operates up to 1 GHz and can be connected to an oscilloscope via a BNC connector. Battery-powered. Micsig OIP1000B

Male terminal block, angled, 2-pin. Pitch 5.0mm. Height 7.8mm. 2EDGRC-5.0-2P

Female terminal block, 5-pin. Pitch 3.81mm. Height 11.1mm. 15EDGK-3.81-5P

Shielded FTP category 5E Ethernet network cable with RJ45 plugs. Lanberg PCF5-10CC-0025-B

eMMC Flash memory module for Hardkernel Odroid N2L computers. 8GB capacity, installed Linux operating system. The set includes a microSD adapter. Hardkernel 8GB eMMC Module N2L Linux

High voltage differential probe. It is characterized by good measurement parameters: with a 100 MHz band and an operating voltage up to 5600 V. The probe has two attenuation factors: 200X and 2000X. Micsig DP20003

Probe for measuring direct and alternating current with a current of up to 30 A. Works in the band up to 100 MHz, it can be connected to the oscilloscope through the UPI connector. It does not require an external power supply. Micsig CP1003

Probe for measuring direct and alternating current with a current of up to 30 A. Works in the band up to 50 MHz, it can be connected to the oscilloscope through the UPI connector. It does not require an external power supply. Micsig CP503

Self-assembly case designed for minicomputers Odroid H3 and Odroid H3+. Equipped with a place for a network card. Hardkernel ODROID-H3 Case Type 6

The expansion board is designed to work with Alchitry Au and Alchitry Cu. The board has four 7-segment LED displays, five buttons, 24 LEDs and 24 DIP switches. SparkFun DEV-17278

Minicomputer with Amlogic S922X processor, which integrates the ARM Cortex-A73 quad-core chip and Cortex-A53 dual-core with Mali-G52 GPU and 4GB of RAM. Additional equipment includes: eMMC memory slot, HDMI, microSD card slot and 40-pin GPIO connector. Hardkernel Odroid N2L

Minicomputer with Amlogic S922X processor, which integrates the ARM Cortex-A73 quad-core chip and Cortex-A53 dual-core with Mali-G52 GPU and 2GB of RAM. Additional equipment includes: eMMC memory slot, HDMI, microSD card slot and 40-pin GPIO connector. Hardkernel Odroid N2L

eMMC Flash memory module for Hardkernel Odroid N2L computers. 16GB capacity, installed Linux operating system. The set includes a microSD adapter. Hardkernel 16GB eMMC Module N2L Linux

9.7" monitor with e-Paper screen equipped with a mini HDMI interface. It offers a resolution of 1200x825 pixels, a wide viewing angle and low power consumption. Waveshare EINK-DISP-97 (EU)