.png)
Category: RETIRED PRODUCTS
There are 12628 products.
Module for learning the basics of electronic engineering; illustrates the relationship between voltage, current, and allows the generation and observation of signals. It has the ability to sample the signal up to 200kSPS in a 16-bit converter. Powered from the USB port. ADALM1000
No product available!
Ribbon Cable, IDC Socket, IDC Socket, 40 Ways, 5.91 ", 150 mm, 2.54 mm
No product available!
Load Cell Amplifier is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. SEN-13230
No product available!
Bluetooth module for mounting in SMD technology with a fully configurable UART interface - transfer speed up to 2 Mb / s. WRL-11786
ATTENTION! A newer version of this product is available.
Click to go to the product page
No product available!
The Arduino GSM Shield connects your Arduino to the internet using the GPRS wireless network. Just plug this module onto your Arduino board, plug in a SIM card from an operator offering GPRS coverage and follow a few simple instructions. You can also make/receive voice calls (you will need an external speaker and microphone circuit) and send/receive SMS messages.
No product available!
The cable allows connecting the ATMEL-ICE programmer to the commissioning set with any connector (operated by the programmer), through individual pin connectors
No product available!
Pre-installed XUbuntu 15.04 or latest version for ODROID-XU3 and XU4. Ready to run out of box 8Gbyte eMMC Version 5.0 interface from Toshiba
No product available!
Pre-installed Android4.4 or latest version for ODROID-XU3 and XU4. Ready to run out of box 8Gbyte eMMC Version 5.0 interface from Toshiba. JEDEC/MMCA version 5.0:HS400 interface with 8bit DDR mode
No product available!
Pre-installed XUbuntu 15.04 or latest version for ODROID-XU3, XU4 and HC1
No product available!
Pre-installed XUbuntu 15.04 or latest version for ODROID-XU3, XU4 and HC1
No product available!
This level shifter board contains 3 x TSX0108E bi-directional level shifter ICs. The 30-pin and 12-pin GPIO ports on the XU4 are converted to the more common 0.1inch (2.54mm) pitch 40-pin header. All the signals can be level shifted to 3.3V or 5V.
No product available!
The Cloudshell for XU4 is an affordable DIY Network Attached Storage (NAS) Solution to create your own personal cloud! It includes a color LCD console display on the front and has room for a 2.5inch HDD/SSD along with the XU4 board inside the CloudShell
No product available!
The Cloudshell for XU4 is an affordable DIY Network Attached Storage (NAS) Solution to create your own personal cloud! It includes a color LCD console display on the front and has room for a 2.5inch HDD/SSD along with the XU4 board inside the CloudShell
No product available!
Cooling Fan X is a cooling fan that can be used to cool any processor that works under heavy load. It can be mounted on the heat sink housing with 4 screws
No product available!
Photon Wearable Shield makes it easy to add the WiFi enabled Photon to any wearables project. Each pin on the Photon is broken out into large sewing pins. Use conductive thread to make your next wearables projects. DEV-13328
No product available!
1-channel monochrome system of adding subtitles on the image (OSD - On-Screen Display) with integrated EEPROM, TSSOP28, Maxim memory
No product available!
Buy the base and top of this case separately to mix-and-match your choice of colors. Recommended to protect the ODROID-XU4 board from accidental damage.
No product available!
No product available!
The controller can control two brush motors, communicating with the master system using USB Micro-B, TTL serial interface, analog signals, as well as signals from the RC apparatus. The current capacity of 5A / channel allows you to control high-power motors. Polol 2394
No product available!
EEPROM CAT93C86LI-G memory; 16kbit; 2K x 8bit; access time: 150ns; Power supply: 1.8 ... 5.5 V; 8-Pin PDIP
No product available!