Category: RETIRED PRODUCTS

Raspberry computer case: Pi 3 model B +, Pi 3 model B, Pi 2 model B and Pi 1 model B + in gray with metal

Pre-installed Ubuntu 14.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode

Pre-installed Ubuntu 16.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung. JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode. The eMMC chipset is only compatible with Amlogic S905 and S805 series(ODROID-C1+ / C0 / C2)

Pre-installed Ubuntu 16.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung. JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode. The eMMC chipset is only compatible with Amlogic S905 and S805 series(ODROID-C1+ / C0 / C2)

Pre-installed Android5.x or latest version. eMMC Version 5.0 interface or higher version from Samsung. JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode. The eMMC chipset is only compatible with Amlogic S905 and S805 series(ODROID-C1+ / C0 / C2)

Pre-installed Ubuntu 16.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung. JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode. The eMMC chipset is only compatible with Amlogic S905 and S805 series(ODROID-C1+ / C0 / C2)

Power Supply 2.5A 5.1V for Raspberry Pi 3 model B - STONTRONICS T5875DV

Pre-installed Ubuntu 14.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode

OS Preinstalled Flash Memory for ODROID-C2 with Linux

Pre-installed Android 4.x or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode

The Raspberry Pi GPIO Triple Expansion Board converts the single GPIO headers on your Raspberry Pi into three parts. DFR0385

Pre-installed Ubuntu 14.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode

5V / 3.1A eXtreme power supply with microUSB plug for all Raspberry Pi computers (including Pi 3 model B and Pi 3 model B +)

Antenna with built-in LNA amplifier with high sensitivity, for mounting in a device using a GPS module. The antenna has a 25mm cable, terminated with a U.FL plug (IPEX). Dimensions of the device: 9 x 9 x 4mm

The GY-GPS6MV1 module is a board containing the U-blox NEO-6M GPS receiver system. The tile also includes RTC backup battery, antenna connector (U.FL), voltage stabilizer and UART signal outputs

Kit: MAXimator, MAXimator Expander, ZL32PRG - USB Blaster PRO

Power Supply 2.5A 5.1V for Raspberry Pi 3 model B - STONTRONICS T5875DV

MYD-JA5D44 Development Board is a complete educational platform. Its heart is the MYIR MYC-JA5D44 module, which was equipped with the Atmel SAMA5D44 processor based on Cortex-A5 cores. The processor can work at a maximum frequency of 600 MHz. Min. RS232, RS485 connectors, HDMI connector, 3.5 mm Jack Audio inputs, microSD memory card slot, 10/100 Mbps Ethernet slot and many more.

This compact, inexpensive plastic gearmotor (brushed DC motor with a 120:1 reduction gearbox) is well suited for use in small robots. While intended for operation at 4.5 V, it should run comfortably in the 3 V to 6 V range.

Battery: Li-Ion; 3.7V; 1000mAh; Outputs: wires with 2-pin JST-PH connector; 50.8 mm x 33.5 x 5.9 mm. PRT-13813