Category: STARTER KITS, PROGRAMMERS, MODULES

A miniature board with dimensions of 20x22 mm with an ATmega32U4 microcontroller. Compatible with Arduino Leonardo. DFRobot DFR0816

Rotary encoder module dedicated to M5StickC/C-CPlus. It integrates AB rotary encoder with push button function and is powered by built-in battery. M5stack U157

Analogue temperature and humidity sensor module based on SHT30 sensor. It is characterized by high reliability and stability with low energy consumption. It is compatible with 3.3V and 5V controllers, such as Arduino, micro:bit, ESP32. DFRobot DFR0588

IoT development board equipped with ESP32 chip with WiFi and Bluetooth, has a USB-UART interface allowing programming via the USB port of the computer. DFRobot DFR0625

Module with a 3-axis MSA311 accelerometer with a configurable measuring range of ±2g/±4g/±8g/±16g. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5309

Module with an IR receiver operating at a frequency of 38 kHz. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020016

JTAG / SWD programmer-debugger with USB and WiFi interface. It supports microcontrollers and microprocessors with Cortex-M, Cortex-A, Cortex-R and ARM7, ARM9 and ARM11 cores of most manufacturers as well as 8051, RISC-V, PIC32, RX. Segger J-Link WiFi (8.14.28)

The module allows you to connect 4 arcade buttons with LED backlight. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5296

Module with ITR9909 proximity sensor that can detect the presence of objects in the range from 9 to 30 cm. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020175

Module with WiFi Espressif ESP32-S2. It integrates the TFT LCD display, SPI Flash memory, LiPo charging circuit and RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5300

Module with real time clock (RTC) DS1307 and CR1225 battery socket. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020013

FeatherWing module with a 2.9" e-paper display featuring a 296×128 px resolution, supporting 4 grayscale levels and based on the SSD1680 driver, designed for Feather-standard boards. Adafruit 4777

Module with L3G4200D (3-axis gyroscope with digital output)

Expansion board for STM32 Nucleo enabling output support in the industry standard. It allows you to control eight galvanically isolated outputs as relays. It has a connector compatible with Arduino® UNO R3. STMicroelectronics X-NUCLEO-OUT02A1

Heart rate measurement module compatible with Arduino and Raspberry Pi (Gravity: Heart Rate Monitor Sensor For Arduino). It uses PPG technique, which in a simple and cheap way is able to measure the changing volume of blood. DFRobot SEN0203

UART-RS485 converter module based on the TD (H) 541S485H chip. Equipped with power isolation and TVS. DFRobot DFR0845

Module with a 4-element 14-segment display. The board is equipped with a Qwiic connector and communicates via the I2C interface. SparkFun COM-16918

Module with 17x7 LED matrix display (119 LEDs) designed to work with micro:bit. It uses the IS31FL3731 driver and communicates via the I2C interface. Pimoroni PIM353

Module with a 4-element 14-segment display. The board is equipped with a Qwiic connector and communicates via the I2C interface. SparkFun COM-18565

Shield for STM32 Nucleo that allows you to add the possibility of operating a three-phase brushless motor (BLDC) or synchronous permanent magnet (PMSM). It uses the L6230 chip for control. X-NUCLEO-IHM07M1