The S9V11F3S5C3 switching step-up/step-down regulator efficiently produces a fixed 3.3 V (default) or 5 V (selectable) output whether it is higher or lower than the input voltage, which can range from 3 V to 16 V. The regulator also has fixed 3.3 V low-voltage cutoff with hysteresis that can be used to prevent battery over-discharge.

Module with 13 QTR type optocoupler with analog output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 40 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4213

Module with 25 QTR type optocoupler with analog output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 50 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4225

DRV8825 Stepper Motor Driver Module for Arduino. It allows you to control two drives, equipped with an XBee connector. DFRobot DRI0023

The S9V11F5S6CMA switching step-up/step-down regulator efficiently produces a fixed 5 V (default) or 6 V (selectable) output whether it is higher or lower than the input voltage, which can range from 2 V to 16 V. (Note: minimum start-up voltage is 3 V, but it operates to 2 V after that.)

The S9V11MACMA switching step-up/step-down regulator efficiently produces a finely adjustable output between 2.5 V and 9 V whether it is higher or lower than the input voltage, which can range from 3 V to 16 V. The regulator also has a precision-adjustable low-voltage cutoff with hysteresis that can be used to prevent battery over-discharge.

This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 V operating range and are efficient enough to deliver a continuous 18 A without a heat sink.

This add-on board makes it easy to control two high-power DC motors with a Raspberry Pi. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 Voperating range and are efficient enough to deliver a continuous 18 A without a heat sink. The drivers offer basic current limiting functionality, and they accept ultrasonic PWM frequencies for quieter operation. 

Monochrome OLED display with a diagonal of 1.3" and a resolution of 128x64 pixels. It has a built-in SH1106 controller, communication via the SPI interface. Pololu 3760

Module with 7 QTRX type optocoupler with RC (digital) output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 40 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4347

Module with 13 QTRX type optocoupler with analog output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 40 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4413

Module with 13 QTRX type optocoupler with RC (digital) output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 40 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4313

A small LCD panel with the ability to control its transparency. The panel can block up to about 95% of light. Adafruit 3627

Module with a color LCD IPS display with a screen diagonal of 4" and a resolution of 720x720 px, dedicated to the Raspberry Pi. Equipped with a capacitive touch screen, communicates via the DSI interface. Pimoroni PIM470

A set with a monochrome camera with a resolution of 0.3 MPx with an OV7251 sensor, a USB adapter and a MIPI adapter. Without IR filter. ArduCAM EK028

Camera with a resolution of 8 MPx with a USB interface. Equipped with CMOS IMX179 sensor with 75° lens, microphone, housing and tripod. ArduCAM UB019701

Camera with OV4689 CMOS sensor with a resolution of 2688x1520 px. It communicates via a parallel interface. ArduCAM U6035

Miniature camera module with OV5647 5MP sensor dedicated to Raspberry Pi Zero and Compute Module. Equipped with a lens with a viewing angle of 160°. ArduCAM B006605