Programming module for AM32 and BLS32 series ESC controllers. It allows you to easily update the controller software via the USB Type-C connector. RhinoESC Crawler

LED strip with COB diodes in cold blue. It is powered by 12 V DC, has a length of 5 m and 384 LEDs/m. Protection level IP20

A dual-channel BLDC controller capable of controlling two motors simultaneously using precise FOC vector control. Equipped with the EG Driver Chip, an INA181A2 amplifier, and a 1 mΩ sensing resistor, it provides accurate current measurement and stable operation at peak currents up to 12 A. It supports a variety of encoders and sensors, and its compatibility with ESP32 modules makes it easy to integrate into projects. Makerbase DUAL FOC PLUS

Module with INA237 sensor designed for power monitoring. Allows measurement of voltages up to 85 VDC and current up to 10 A. Uses a 16-bit ADC for precise and accurate readings available via the I2C interface. Adafruit 6340

ARM Cortex-M0 CPU, 16kB Flash, 4kB RAM, 1xUART, 1xI2C, 1xSPI, ADC, TSSOP20, STM, RoHS

RGB LED matrix display with 64x32 resolution (2048 LEDs). It has a HUB75 interface and can work with Raspberry Pi, Arduino or ESP32. Waveshare RGB-Matrix-P2.5-64x32

LED strip with COB diodes in blue. It is powered by 12 V DC, has a length of 5 m and 384 LEDs/m. Protection level IP20

Female-female cable, 63 cm long, with JST-SH 6-pin plug on both sides. Suitable for micro DC motor encoders with gear. Pololu 4769

A module for building a rear bicycle light using 1000 mCd red LEDs. Power supplied by AA batteries, which are not included in the kit. Kitronik 2106

Easy-to-install indicator signaling the operation of devices or systems, with an attached resistor and adapted to work with 12V supply voltage

Male terminal block, angled, 3-pin. Pitch 3.81mm. Height 7mm. 15EDGRC. Set of 10 pieces

32-bit microcontroller from the STM32F4 family with ARM Cortex-M4 core, 1MB Flash memory, 256kB SRAM memory, 180MHz, I2C, ISPI, UART / USART, USB OTG, 1.8 ... 3.6V, 208LQFP, STM, RoHS

Module with a steam sensor. It can be supplied with the voltage of 3.3 V or 5 V. It has an analog output. DFRobot SEN0121

Female terminal block, angled, 2-pin. Pitch 5.0mm. Height 15mm. 2EDGK-5.0-2P. Set of 5 pieces

Current-to-voltage converter module designed for devices with a current signal output. It allows linear conversion of current signals from 0 to 25 mA into voltage signals from 0 to 3 V. DFRrobot SEN0262

32-bit ARM Cortex-M0 microcontroller, 128 kB flash and 8 kB SRAM, 40 segment x 4 LCD driver, NXP, LQFP100, RoHS

32MP AI camera that enables neural network processing and image analysis directly on the device, supporting AI models after conversion. Equipped with the 4 TOPS RVC2 architecture, with features such as distortion correction, 2D object tracking, and dynamic autofocus, it is ideal for complex computer vision tasks with fast data transfer via USB-C. Luxonis OAK-1 MAX

The POT0019 potentiometer enables precise adjustment of electrical parameters in applications requiring stability and accuracy. Designed for panel mounting, it is equipped with flat solder terminals and resistant to long-term use.

4-core cable with a length of 300 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 5384