Category: Amplifier modules
There are 134 products.
Class A power amplifier with one channel (mono) with the power of 10 W. Built on the popular design of J. Hood from 1969
The module with a digital stereo audio amplifier is equipped with Bluetooth communication. The system allows you to connect two speakers with an impedance of 6 Ω or 8 Ω with a power of 6 W per channel
The PAM8403 class D stereo digital audio amplifier module is equipped with Bluetooth communication. The system allows you to connect two speakers with an impedance from 4 to 8 Ω and a power of 3 W
Class-D mono audio amplifier module based on the MAX98357 chip. It can work with a 4 to 8 ohm speaker of up to 2.5 W and communicates via an I2S interface. DFRobot DFR0954
Digital stereo audio amplifier with Bluetooth 5.0 module. It has two channels with a power of 100 W and can work with speakers from 4 to 8 Ω. Powered with voltage from 5 to 24 V. 1002M
Audio module with DAC, stereo amplifier and display, designed to work with the Raspberry Pi. Pimoroni PIM484
Audio amplifier module with three output channels. It can be powered from 12 to 24 V and has two 50 W outputs (left and right) and one 100 W output (bass). Equipped with Bluetooth 5.0 communication
Audio amplifier module with three output channels. It can be powered with the voltage from 12 to 18 V and has two outputs with a power of 10 W (left and right) and one with a power of 20 W (bass)
Audio module with speakers designed to work with the Raspberry Pi Pico. Waveshare Pico-Audio
Module with the PAM8904 controller designed specifically to control piezoelectric elements. The amplifier operates over a wide frequency range, up to 300 kHz, and allows for gain up to approximately 13 Vpp. Adafruit 5791
Class D digital audio amplifier with Bluetooth module. It has two channels with a power of 50 W and can work with speakers from 4 to 8 Ω. It is powered with the voltage in the range from 9 to 24 V. NS-01G
LM386 audio amplifier module in a set with a loudspeaker. The board is equipped with a Grove connector and is controlled by a PWM signal. Seeed Studio 101020853
Audio module with DAC, headphone amplifier and display, designed to work with the Raspberry Pi. It is based on the PCM5100A system and communicates via the I2S interface. Pimoroni PIM482
Class D digital audio amplifier with Bluetooth module. It has two channels with a power of 50 W and can work with speakers from 4 to 8 Ω. It is powered with the voltage in the range from 9 to 24 V. NS-01G
Class D digital audio amplifier with Bluetooth 5.0 module. It has two channels with a power of 50 W and can work with speakers from 4 to 16 Ω. It is powered with the voltage ranging from 9 to 24 V.
Module with an AB class amplifier based on the Boomer® LM4853 system. It can work in two modes: mono (power 1.5 W, load 4 Ω) or stereo (power 300 mW, load 8 Ω). It has a potentiometer for power control and gain control for the left and right channel. SparkFun DEV-14475
PAM8302 Class D mono digital audio amplifier module. The system allows you to connect one loudspeaker with an impedance of 4 to 8 Ω and a power of 2.5 W. The board is equipped with a STEMMA connector. Adafruit 5647
Class D stereo sound amplifier based on the Texas Instruments TPA2016D2 circuit. It can work with 4 Ω speakers with power up to 2.8 W or 8 Ω with power up to 1.7 W in stereo mode. SparkFun DEV-20690
Class D digital audio amplifier with Bluetooth 5.0 module. It has two channels with a power of 50 W and can work with speakers from 4 to 8 Ω. It is powered with the voltage ranging from 9 to 24 V
Class A power amplifier with one channel (mono) with the power of 10 W. Built on the popular design of J. Hood from 1969.