Miniature Brushless Motor ESC Controller 7A 1-2S BLheli_S XSD7A

ESC controller module for a brushless motor with a current capacity of up to 40 A. It can work with LiPo packages from 3S to 6S. Uses BLHeli_32 software. Skystars Talon32

The ODrive3.6 ESC speed controller is designed to power two three-phase brushless motors in various applications, such as driving robots, walking robots or gimbals. Supports input voltage range from 12 V to 56 V and maximum current up to 60 A. Makerbase ODrive3.6

This BLDC motor controller, based on the Allegro A89301 chip, enables sensorless control over a wide voltage range from 5.5 V to 48 V and phase current up to 11 A without additional cooling. It supports four control modes: analog voltage, PWM signal, pulse frequency, and via an I²C interface with the ability to configure parameters and save settings to EEPROM. The Field-Oriented Control (FOC) algorithm ensures quiet and efficient operation, while built-in protection protects the system against short circuits, reverse polarity, and undervoltage. Pololu 5356

Brushless motor driver module (ESC regulator) with current efficiency up to 30 A

An advanced speed controller designed to power three-phase brushless motors in various applications, such as driving robots, walking robots or gimbals. Supports input voltage range from 12V to 56V. Maximum constant current is 60A. Makerbase ODrive-S

The X-NUCLEO-IHM16M1 motor driver expansion board is based on the STSPIN830 monolithic driver for three-phase brushless motors. It represents an affordable, easy-to-use solution for driving brushless motors in your STM32 Nucleo project, implementing single and three-shunt current sensing

Controller of three-phase BLDC motors based on Trinamic\'s TMC6300 chip. Allows motion control of drives with a current consumption of up to 2 A. SparkFun ROB-21220

The X-NUCLEO-IHM17M1 is a low voltage three-phase brushless DC motor driver expansion board based on the STSPIN233 for STM32 Nucleo. It provides an affordable and easy-to-use solution for the implementation of portable motor driving applications such as thermal printers, robotics and toys

Shield for STM32 Nucleo that allows you to add the possibility of operating a three-phase brushless motor (BLDC) or synchronous permanent magnet (PMSM). It uses the L6230 chip for control. X-NUCLEO-IHM07M1

Waveshare DDSM Driver HAT (B) is an advanced hub motor driver for DDSM400 motors, based on the ESP32, featuring both wired (USB, UART) and wireless (WiFi, ESP-NOW) communication. It supports control of up to 6 motors using JSON commands and integrates with Raspberry Pi, making it a suitable solution for mobile robotics and multi-motor system projects.

ESC controller module for a brushless motor with a current capacity of up to 120 A. It can work with LiPo packs from 5S to 12S. Uses BLHeli_32 software. FLYCOLOR X-CROSS HV

Driver for three-phase BLDC motors based on the TMC6300 system from Trinamic. It allows you to control the movement of drives with a voltage of 2 to 11 V and a current consumption of up to 2 A. SparkFun ROB-21867

A dual-channel BLDC controller capable of controlling two motors simultaneously using precise FOC vector control. Equipped with the EG Driver Chip, an INA181A2 amplifier, and a 1 mΩ sensing resistor, it provides accurate current measurement and stable operation at peak currents up to 12 A. It supports a variety of encoders and sensors, and its compatibility with ESP32 modules makes it easy to integrate into projects. Makerbase DUAL FOC PLUS

Brushless DC motor (BLDC) driver with speed control by potentiometer. It can operate motors powered with a voltage from 7 to 12 V with a current consumption of up to 1.2 A

Brushless DC motor (BLDC) driver. It can operate motors powered with a voltage from 6 to 20 V with a current consumption of up to 3 A

Brushless motor driver module (ESC regulator) with current efficiency up to 35 A