- Out-of-Stock
UCCB - USB-CAN converter
ID: 580286
USB - CAN converter module. It allows the device to be connected to a computer (USB) or microcontroller (UART) via the CAN bus. USB CAN CONVERTER (UCCB)
Description
USB - CAN converter module based on the STM32F042C6 microcontroller and the TJA1050T CAN system. It has a built-in voltage stabilizer ESD protection. It allows you to connect to a computer (via USB) or microcontroller (via UART) the device via the CAN bus. The converter has a USB type A connector and a screw socket. Through the computer it is visible as a COM port and works with standard terminals.
Full documentation and additional software is available in the product repository.
Connector description:
- 5V - 5V power supply
- GND - Ground supply
- TX - UART communication line
- RX - UART communication line
Features
- CAN version 2.0 support
- Receiving and sending normal and extended frames
- Choice of communication speed (from 60 kb / s to 1 Mb / s)
- Loopback mode
- Frame filtering (up to 28 filters)
- Listening mode
- Supply voltage 5 V
- Terminating resistors
- SocketCAN support
- GSUSB support (requires different firmware)
- Dimensions: 27 x 15 mm (without USB connector)
580286
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 5V Arduino boards. It can also be used for general serial applications. DEV-09716
zł92.15
24h
Available quantity: 2
Available
Premium Jumper Wire 10-Pieces Green Assortment M-M (Male-to-male)
zł6.90
24h
Available quantity: 23
Available
A set of 10 white male-male white leads, 15 cm long, for contact plates. CAB_M-M (10-15 W)
zł8.91
24h
Available quantity: 10
Available
Set of 10 pcs. Male blue male cables, 15 cm long, for contact plates. CAB_M-M (10-15-B)
zł7.31
24h
Available quantity: 15
Available
A set of 10 white male-male white wires, 30 cm long, for contact plates. CAB_M-M (10-30 W)
zł7.53
24h
Available quantity: 10
Available
A set of 10 green male-male cables with a length of 30 cm for contact plates. CAB_M-M (10-30-G)
zł6.90
24h
Available quantity: 10
Available
A set of 10 pieces of blue male-male cables 30 cm long for contact plates. CAB_M-M (10-30-B)
zł8.89
24h
Available quantity: 10
Available
Available
CP2102 USB to UART Module, USB micro connector
zł19.54
24h
Available quantity: 11
Available
USB - LIN bus converter module. It allows you to connect devices to your computer via the LIN bus. LIN USB CONVERTER (LUC)
zł106.91
24h
Available quantity: 6
Available
Other products in the same category (16)
No product available!
No product available!
No product available!
AVT kit for self-assembly of a remotely controlled 4-channel switch. AVT5599 B
Retired
No product available!
No product available!
No product available!
No product available!
Male terminal block, angled, 11-pin. Pitch 5.0mm. Height 7.8mm. 2EDGRC-5.0-11P
Retired
No product available!
SmartLED Shield driver (V4) for SmartMatrix series displays, for use with Teensy 3.2, Teensy 3.5 and Teensy 3.6. It is also possible to connect LED Dotstar or APA102 displays. Adafruit 1902
Retired
No product available!
No product available!
No product available!
No product available!
No product available!
Development board with microcontroller from the Freescale KINETIS L family (Cortex-M0+) and MEMS 7DoF sensors.
Retired
No product available!
No product available!
Marek Domański
Delivery date unknown
No product available!
USB - CAN converter module. It allows the device to be connected to a computer (USB) or microcontroller (UART) via the CAN bus. USB CAN CONVERTER (UCCB)