DAQ device based on Ethernet communication and equipped with 24 digital inputs/outputs and a counter input. Users can remotely access and configure the device with software over the Internet.
The module has 24 digital I/O lines configured as three 8-bit ports. Each bit is individually configurable as input or output. Users can enable the digital bit configured to change the exit state when the connection to the host is established or broken. Data can be transferred at up to 5kS/s when the device and host are connected via Ethernet to the same local area network, and the typical throughput depends on the system. All DIO lines are pulled up to 5V by default via 47kΩ resistors via three built-in jumpers - each jumper configures one 8-bit digital port and can be easily changed as a pull-down. Additionally, the user has at his disposal a 32-bit event counter that counts TTL pulses and processes signals with a frequency of up to 10 MHz.
Extensive software support includes DAQami - an optional out-of-the-box data capture, visualization and signal generation application. Data can be viewed in real time or after acquisition on user-configurable screens. Drivers for the most popular applications and programming languages are also included, including Visual C++, Visual C#, Visual Basic.NET, DASYLab, LabVIEW, MATLAB, and Python.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
DAQ device based on USB communication and equipped with 8 SE analog inputs, 8 digital inputs / outputs and one 32-bit counter. It offers 16-bit resolution and a sampling rate of 100 kS / s per channel. Digilent 6069-410-015
No product available!
USB based DAQ device with 8 SE/4 DIFF analog inputs, up to four analog outputs, 16 digital inputs/outputs and one 32-bit counter. It offers 13-bit resolution and a sampling rate of 1 MS/s. Digilent 6069-410-017
No product available!
DAQ device based on USB communication and equipped with 96 digital inputs/outputs and a 32-bit counter. Digilent 6069-410-032
No product available!
8-channel IO expander with 6 analog inputs. It communicates via the USB interface. Version with Pull-Up resistors. Numato Lab GP80001P
No product available!
An 4-channel I2C expander module, which is based on the TCA9546A chip. It allows connecting several devices with the same address to a single I2C interface. Adafruit 5664
No product available!
Measurement module with RS485 interface. It has two voltage measurement inputs in the range of 0 to 5 V and 0 to 10 V and two current measurement inputs in the range of 0 to 20 mA. Supports the Modbus RTU protocol
No product available!
64-channel IO expander with 32 analog inputs. It communicates via the USB interface. Numato Lab GP640001
No product available!
Module with a 16-channel GPIO expander with the ability to control LEDs. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4886
8-channel IO expander with 6 analog inputs. It communicates via the USB interface. Version without Pull-Up resistors. Numato Lab GP80001
No product available!
Module with 8 digital inputs and 4 relays with a maximum switching current of 2 A. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP8024ADAM
Module with 16 IO pins and 8 analog inputs. It communicates via the RS485, USB or Ethernet interface and supports the Modbus RTU/TCP protocol. Numato Lab NLGM1001-A
No product available!
16-channel GPIO expander with an I2C interface microcontroller can interface with 16 fully configurable digital input/output pins. It can produce PWM signals, so you can dim LEDs. It can be set to blink or even breathe pins at varying rates. With a built-in keypad engine, it can interface with up to 64 buttons set up in an 8x8 matrix. BOB-13601
Module with 16 digital inputs. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP8026ADAM
No product available!
16-channel IO expander with 7 analog inputs with 10-bit resolution. Communicates via USB interface. It has compact dimensions, making it suitable for small devices. Version with connector at the top. Numato Lab GP160002
Module with 8 analog inputs for voltage measurement in the range from 0 to 10 V. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP3084ADAM
8-channel IO expander with 6 analog inputs with 10-bit resolution. Communicates via USB interface. It has compact dimensions, making it suitable for small devices. Numato Lab GP80002
No product available!
KAmod I2C Hub8 enables splitting the I2C bus into eight independent channels with a voltage translation function, which allows effective integration of multiple devices with repeating addresses. The module is recommended for advanced microprocessor projects with bus separation requirements and diverse voltage levels.
8-channel solenoid driver controlled via I2C. Compatible with 3V/5V logic, features STEMMA QT / Qwiic connectors. Adafruit 6318
DAQ device based on Ethernet communication and equipped with 24 digital inputs/outputs and a counter input. It allows you to control devices via the Internet. Digilent 6069-410-052