Categories - Official Raspberry Pi distributor

New products

OpenVINO Starter Kit Set - FPGA development kit View larger

OpenVINO Starter Kit Set - FPGA development kit (EDU)

[EDUCATIONAL PRICE] FPGA starter kit equipped with Cyclone V GT with 301K LE and minicomputer with Intel Celeron Dual Core (64 GB eMMC, 4 GB RAM). The FPGA module has 1 GB DDR3 memory, 64 MB SDRAM memory, UART-USB interface and extensions such as GPIO and Arduino. Terasic P0650

More details

ID: 576641

854,15€ gross (23% VAT)
694,43€ net

Add to wishlist

More info

ATTENTION! This product is for academic recipients (students and academic teachers) only!

After the ordering, please send us by e-mail the data listed below:

  • the name and last name
  • position (student, teacher)
  • e-mail (with the University domain)
  • University name
  • Facultie / Section
  • University address
  • University phone no.
  • Notice! Students must send a copy of University Identity Card (by e-mail)


OpenVINO is an FPGA starter kit in the form of a card with a PCIe connector and a PC kit with an Intel Celeron Dual Core chip. The kit is equipped with a programmable Cyclone V GT system with 301K LE and supports PCIe Gen 2x4. FPGA has 1 GB of DDR3 memory, 64 MB of SDRAM memory, UART-USB interface and extensions such as GPIO or allowing to connect Arduino extensions. The PC system is equipped with 64 GB eMMC memory and 4 GB DDR4 RAM. This makes the OpenVINO starter kit a configurable platform combining high computing performance and low energy consumption.

The OpenVINO package contains reference projects for all peripherals of the set and detailed instructions for programmers.


CPU system (PC)

  • CPU: Celeron Dual Core
  • Memory:
    • 32GB eMMC
    • 4GB DDR4
  • Interface
    • Mini PCIe
    • Ethernet
    • HDMI
    • UART
    • USB
  • Power Input: 5V DC

FPGA OpenVINO Starter Kit

  • FPGA Device (Cyclone V)
    • 301K Programmable Logic Elements
    • 13,917 Kbits embedded memory
    • Eight Fractional PLLs
    • Two Hard Memory Controllers
    • Nine Transceivers (the GT speed is 6.144G, and GX speed is 3.125G )
  • Configuration and Debug
    • Quad Serial Configuration device-EPCQ256
    • On-Board USB Blaster II (Mini-B USB connector)
  • Memory Device
    • 64MB (32M x16) SDRAM
    • 1GB (2 x256M x16) DDR3 SDRAM
  • Communication
  • UART to USB(Mini-B USB connector)
  • GT device supports PCIe Gen2x 4(GX device supports PCIe Gen1x 4)
  • Expansion I/O
    • 2 x40 GPIO Header
      • 36 General GPIO Pins
      • Support 8 pairs LVDS TX and 8 pairs LVDS RX
      • Diode protection circuit
      • Configurable I/O standards: 1.5/1.8/2.5/3.3V
    • One Arduino Uno Revision 3 Expansion HearderSMA IN/OUT 3.3V single port
  • Analog ADC
  • SPI Interface
  • 500Ksps Sampling Rate
  • Eight Channels
  • 12-Bit Resolution
  • Analog Input Range:0 ~ 4.096 V
  • Resolution: 12-bit
  • Digital IO
  • Diode protection circuit
  • Switches, Buttons, LED, and 7-Segments
    • 5 User Buttons (4 normal buttons, one CPU_RESET_n)
    • 4 User Switches
    • 4 LEDs
    • 2 7-Segments
  • Power
    • 12V DC input
    • PCIe 12V Input
  • Cooling
    • 12V, 5000 Speed Fan
    • Dimensions: 167.6 x 83.2 mm

Description of components and connectors

Block diagram

Kit contains

  • OpenVINO Starter Kit Set
  • USB 3.0 Cable
  • Mini USB Cable
  • 12V Power Supply (for FPGA Board)
  • 5V power Supply (for PC system)