Best sellers

Development board based on the ESP32-C3-MINI-1 module. It offers the ability to connect via WiFi, Bluetooth version 5 and Bluetooth Mesh. It is equipped with sensors, such as the SHTC3 temperature and humidity sensor or the IMU 6 DoF ICM-42670-P sensor. Espressif Systems ESP32-C3-DevKit-RUST-1

The XTAR X4 is a four-channel automatic charger with deep discharge recovery and a three-phase charging algorithm, compatible with a wide range of Li-ion and Ni-MH battery sizes. With both AC and USB power options and a built-in power bank feature, it\'s ideal for both home and mobile use.

Module with an analog MQ5 LPG sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0130

Module with a temperature and humidity sensor DHT22. It allows you to measure humidity in the range from 0 to 100% and temperature from -40 to 80℃. DFRobot SEN0137

True RMS clamp multimeter for accurate AC current measurements up to 600 A and AC/DC voltage up to 600 V. The device offers kWh energy recording, three-phase power measurements, a peak-RMS function, and a quick continuity test. Meets CAT III 600 V safety standards, has 6 kV surge protection, and a backlit display, making it an ideal choice for professionals. Brymen BM357s

Module with an analog MQ8 hydrogen sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0133

The JBC-C210008 tip with a screwdriver-shaped end 1.3 × 0.6 mm is compatible with the T210 handle and JBC soldering stations. The integrated heater provides precise temperature control during soldering of through-hole and surface-mount components.

The JBC-C210001 tip with a 0.3 mm conical end provides high precision for soldering small components. Designed for the JBC T210 handle, it is used in precision electronics and SMD device servicing.

Vorel - 76640

VETUS W8 tweezers with ceramic tips and a stainless steel handle combine high chemical and temperature resistance with precision work. Dedicated to applications in electronics and servicing, especially where safe handling of components sensitive to ESD and high temperature is required.

Keyboard module with five colored buttons. The board is equipped with a Gravity connector and has an analog output. Powered with the voltage of 3.3 V or 5 V. DFRobot DFR0075

The infrared distance sensor enables the detection of objects in the range from 3 to 50cm. The sensor has a digital output, the detection threshold is adjusted by a potentiometer. DFRobot SEN0164

Module with a button, LED diode and a white cap. DFRobot DFR0029-W

Module with a buzzer (without generator) controlled by a digital interface. It allows you to generate simple sounds by changing the frequency of the control signal. DFRobot DFR0032

Module with an analog light sensor. It consists of a photoresistor and a LED. Equipped with a Gravity connector. DFRobot DFR0022

Permanent cylindrical neodymium magnet with a diameter of 8 mm and a height of 1 mm. Set of 10 pcs

4-digit, 8-segment LED display module with 8-level brightness adjustment. Communication via the I2C interface. DFRobot DFR0645-R

4-digit, 8-segment LED display module with 8-level brightness adjustment. Communication via the I2C interface. DFRobot DFR0645-G

C-mount lens. Focal length 50mm, FoV 10°(H), 7°(V). Designed to work with the Raspberry Pi HQ camera. ArduCAM LN054

Module with the SX1276 868 MHz system for LoRa communication, designed for FireBeetle boards. It communicates via the SPI interface. DFRobot TEL0125