

Bluetooth 4.0 module based on the CSR8635 chip. The CSR8635 is an audio platform for wired and wireless applications that integrates an ultra-low power DSP and application processor with built-in flash memory, high-performance stereo codec, power management subsystem, and LED drivers. The CSR configuration tools and development kit provide a flexible and efficient development platform for designing advanced and high-quality stereo products with Bluetooth connectivity. The main area of application of the module are Bluetooth speakers, Bluetooth car kits and headsets. The module has a built-in antenna and pins for edge connectors, which allows for surface mounting of the module in your own design.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
A module that combines GSM/GPRS/GNSS and BT 3.0 technologies. It is available in a small, easy to solder LCC housing and has a low power consumption up to 1.2 mA. Quectel MC60CA
Module with SIM868 designed for GSM, GPRS communication and GNSS positioning. It can communicate within the Bluetooth 3.0 standard. SB Components 21895
Bluetooth module v2.0 + EDR (master / slave), controlled by AT + commands with built-in antenna.
Advanced wireless communication module, based on the Bluetooth 5.4 stack (Bluetooth® Low Energy, BLE), which was designed using the efficient Nordic NRF52805 SOC system. The module offers support for the UART interface, available only in peripheral mode, which allows for effective operation as a data bridge (Data Bridge). Sparkfun WRL-25466
No product available!
Bluetooth 4.0 dongle as a USB adapter. Works with bluetooth devices such as speakers, headsets, smartphones, tablets, keyboards, mice, printers, projectors etc.
Bluetooth audio receiver module enclosed in a housing that enables wireless transmission of sounds. It is equipped with a PCB antenna, microphone, 3.5 mm audio jack and control buttons
An integrated module combining WiFi, Bluetooth 4.0 and FM radio. It has derived SDIO, UART and PCM interfaces. Ampak AP6335
Bluetooth module v2.0 + EDR, controlled by AT + commands with built-in antenna.
A development board that combines the u-blox NINA-B306 Bluetooth module, the ISM330DHCX 6DoF IMU sensor, and the BME280 atmospheric pressure sensor. It has a built-in Qwiic connector and LiPo battery connector as well as a charger and LiPo parameters monitor. SparkFun WRL-20854
No product available!
Expansion board with BlueNRG-M0 module compatible with Bluetooth v4.2. It is compatible with the ST morpho connector system (unmounted) and Arduino UNO R3. Communication with the module is via the SPI interface. STMicroelectronics X-NUCLEO-IDB05A2
Expander (shield) compatible with Arduino and NUCLEO (STM32) systems, equipped with a Bluetooth 4.1 (BLE) radio module from the SPBTLE-RF family
Bluetooth module with integrated HC-08 system. Thanks to the angular pin connector with the bus signals, it is possible to easily connect the module to the contact plate or wires
No product available!
Bluetooth 4.0 BLE module powered with 3.3V voltage based on SOC TI CC2541 (On Chip). The module has a range of up to 10m and communicates via the UART interface.
Adafruit 2269 - Bluefruit LE Sniffer - Bluetooth Low Energy (BLE 4.0) - nRF51822 - v1.0
Bluetooth 4.0 module based on the CSR8635 chip designed for Bluetooth audio applications. The module has a built-in antenna and pins for edge connectors.