ACHS-7124 Current Sensor Carrier ±40A
ID: 577697
5906623479948
zł18.82
Tax included
zł15.30 tax excl.
This board is a simple carrier of Broadcom’s bidirectional ±40A ACHS-7124 Hall effect-based linear current sensor, which offers a low-resistance (~0.7 mΩ) current path and electrical isolation up to 3 kV RMS. Pololu 4033
Description
This board is a simple carrier of Broadcom’s bidirectional ±40A ACHS-7124 Hall effect-based linear current sensor, which offers a low-resistance (~0.7 mΩ) current path and electrical isolation up to 3 kV RMS. This version accepts a bidirectional current input with a magnitude up to 40 A and outputs a proportional analog voltage (50 mV/A) centered at 2.5 V with a typical error of ±1.5%. It operates from 4.5 V to 5.5 V and is intended for use in 5 V systems.
Futures
- Measurement range : -40 ~ 40 A
- Electrical resistance: 0.7 mΩ
- Electrical insulation: up to 3 kV
- Interface: analog signal
- Robust sensor IC can tolerate 100 ms transient current spikes up to 100 A
- Operating temperature: -40 ~ 110 ° C
- Dimensions: 17.8 x 20.3 mm
- Weight: 1.5 g
Kit includes:
- ACHS-7124 module
- Goldpin connector
577697
Data sheet
- Interface
- Sygnał analogowy
- Zakres pomiarowy
- ±40 A
- Sposób podłączenia
- Szeregowy
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Board with ATmega2560 microcontroller (256 kB Flash, 8 kB RAM, 4 kB EEPROM) clocked at 16 MHz. USB-UART converter based on the ATmega16u2 chip. The user has at his disposal, among others: 54 I/O lines, 14 PWM channels, 16 analog inputs.
zł79.85
Delivery date unknown
No product available!
Board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface
zł53.71
24h
Available quantity: 15
Available
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.57
24h
Available quantity: 150
Available
Set - two connecting cables (with clamped insulated bushes), matching ARK connectors (suitable for conductors with a cross-section> 2mm ^ 2). The wires have a length of 30cm, the color of wires: blue, red
zł7.27
24h
Available quantity: 12
Available
Li-Po battery with a rated voltage of 3.7 V and a capacity of 4000 mAh, equipped with a PCM protection and a 2.5 JST-RCY connector. Akyga LP805080
zł14.07
Delivery date unknown
No product available!
Other products in the same category (16)
ACS714 Current Sensor Carrier -5 to +5A
zł107.82
24h
Available quantity: 1
Available
ACS714 Current Sensor Carrier -30 to +30A
zł49.70
24h
Available quantity: 2
Available
ACS711EX Current Sensor Carrier -31A to +31A
zł19.98
24h
Available quantity: 4
Available
ACS711EX Current Sensor Carrier -15.5A to +15.5A
zł20.06
24h
Available quantity: 5
Available
The current measurement of 0 - 30A is carried out by the ACS712-30 system based on the Hall effect. The sensitivity of the system is 66mV / A (analog signal).
zł6.86
4 weeks
No product available!
No product available!
No product available!
No product available!
No product available!
Available
The current measurement with the value 0-20A is carried out by the ACS712-05 system based on the Hall effect. The sensitivity of the system is 100mV / A (analogue signal) .modACS712-20
zł14.97
24h
Available quantity: 21
Available
The current measurement with a value of 0 - 5A is realized by the ACS712-05 system based on the Hall effect. The system sensitivity is 185mV / A (analog signal).
zł8.95
4 weeks
No product available!
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 20 A. DFRobot SEN0211
zł91.49
24h
Available quantity: 2
Available
The module with a TA12-200 current sensor with a measuring range of alternating current up to 5 A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020027
zł41.34
24h
Available quantity: 1
Available
Module with an analog current sensor. Enables measurement of alternating and direct current up to 20 A. DFRobot SEN0214
zł40.22
24h
Available quantity: 1
Available
Module with INA219 system with bi-directional current meter
zł10.01
4 weeks
No product available!
This board is a simple carrier of Broadcom’s bidirectional ±40A ACHS-7124 Hall effect-based linear current sensor, which offers a low-resistance (~0.7 mΩ) current path and electrical isolation up to 3 kV RMS. Pololu 4033