![Czujnik odległości VL53L0X 3 - 200 cm w technologii ToF z regulatorem napięcia Czujnik odległości VL53L0X 3 - 200 cm w technologii ToF z regulatorem napięcia](https://kamami.pl/27823-large_default/pololu-2490-vl53l0x-time-of-flight-distance-sensor-carrier-with-voltage-regulator-200cm-max.jpg)
![Czujnik odległości VL53L0X 3 - 200 cm w technologii ToF z regulatorem napięcia Czujnik odległości VL53L0X 3 - 200 cm w technologii ToF z regulatorem napięcia](https://kamami.pl/27823-large_default/pololu-2490-vl53l0x-time-of-flight-distance-sensor-carrier-with-voltage-regulator-200cm-max.jpg)
zł55.35 tax excl.
This sensor is a carrier/breakout board for ST’s VL53L0X laser-ranging sensor, which measures the range to a target object up to 2 m away.
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
The VL53L0X from ST Microelectronics is a time-of-flight ranging system integrated into a compact module. This board is a carrier for the VL53L0X, so we recommend careful reading of the VL53L0X datasheet (1MB pdf) before using this product.
The VL53L0 uses ST’s FlightSense technology to precisely measure how long it takes for emitted pulses of infrared laser light to reach the nearest object and be reflected back to a detector, so it can be considered a tiny, self-contained lidar system. This time-of-flight (TOF) measurement enables it to accurately determine the absolute distance to a target without the object’s reflectance greatly influencing the measurement. The sensor can report distances of up to 2 m (6.6 ft) with 1 mm resolution, but its effective range and accuracy (noise) depend heavily on ambient conditions and target characteristics like reflectance and size, as well as the sensor configuration. (The sensor’s accuracy is specified to range from ±3% at best to over ±10% in less optimal conditions.)
Ranging measurements are available through the sensor’s I²C (TWI) interface, which is also used to configure sensor settings, and the sensor provides two additional pins: a shutdown input and an interrupt output.
The VL53L0X is a great IC, but its small, leadless, LGA package makes it difficult for the typical student or hobbyist to use. It also operates at a recommended voltage of 2.8 V, which can make interfacing difficult for microcontrollers operating at 3.3 V or 5 V. Our breakout board addresses these issues, making it easier to get started using the sensor, while keeping the overall size as small as possible.
The carrier board includes a low-dropout linear voltage regulator that provides the 2.8 V required by the VL53L0X, which allows the sensor to be powered from a 2.6 V to 5.5 V supply. The regulator output is available on the VDD pin and can supply almost 150 mA to external devices. The breakout board also includes a circuit that shifts the I²C clock and data lines to the same logic voltage level as the supplied VIN, making it simple to interface the board with 3.3 V or 5 V systems, and the board’s 0.1″ pin spacing makes it easy to use with standard solderless breadboards and 0.1″ perfboards. The board ships fully populated with its SMD components, including the VL53L0X, as shown in the product picture.
For a similar but shorter-range sensor (up to 20 cm, or 60 cm with reduced resolution) that includes ambient light sensing functionality, see our VL6180X carrier.
A 1×7 strip of 0.1″ header pins and a 1×7 strip of 0.1″ right-angle header pins are included, as shown in the picture below. You can solder the header strip of your choice to the board for use with custom cables or solderless breadboards, or you can solder wires directly to the board itself for more compact installations.
Using the VL53L0XThe board has two mounting holes spaced 0.5″ apart that work with #2 and M2 screws (not included).
Important note: This product might ship with a protective liner covering the sensor IC. The liner must be removed for proper sensing performance.
A minimum of four connections is necessary to use the VL53L0X board: VIN, GND, SCL, and SDA. The VIN pin should be connected to a 2.6 V to 5.5 V source, and GND should be connected to 0 volts. An on-board linear voltage regulator converts VIN to a 2.8 V supply for the VL53L0X IC.
The I²C pins, SCL and SDA, are connected to built-in level-shifters that make them safe to use at voltages over 2.8 V; they should be connected to an I²C bus operating at the same logic level as VIN.
The XSHUT pin is an input and the GPIO1 pin is an open-drain output; both pins are pulled up to 2.8 V by the board. They are not connected to level-shifters on the board and are not 5V-tolerant, but they are usable as-is with many 3.3 V and 5 V microcontrollers: the microcontroller can read the GPIO1 output as long as its logic high threshold is below 2.8 V, and the microcontroller can alternate its own output between low and high-impedance states to drive the XSHUT pin. Alternatively, our 4-channel bidirectional logic level shifter can be used externally with those pins.
PIN | Description |
---|---|
VDD | Regulated 2.8 V output. Almost 150 mA is available to power external components. (If you want to bypass the internal regulator, you can instead use this pin as a 2.8 V input with VIN disconnected.) |
VIN | This is the main 2.6 V to 5.5 V power supply connection. The SCL and SDA level shifters pull the I²C lines high to this level. |
GND | The ground (0 V) connection for your power supply. Your I²C control source must also share a common ground with this board. |
SDA | Level-shifted I²C data line: HIGH is VIN, LOW is 0 V |
SCL | Level-shifted I²C clock line: HIGH is VIN, LOW is 0 V |
XSHUT | This pin is an active-low shutdown input; the board pulls it up to VDD to enable the sensor by default. Driving this pin low puts the sensor into hardware standby. This input is not level-shifted. |
GPIO1 | Programmable interrupt output (VDD logic level). This output is not level-shifted. |
The schematic shows the additional components the carrier board incorporates to make the VL53L0 easier to use, including the voltage regulator that allows the board to be powered from a 2.6 V to 5.5 V supply and the level-shifter circuit that allows for I²C communication at the same logic voltage level as VIN. This schematic is also available as a downloadable PDF (100k pdf).
The VL53L0X can be configured and its distance readings can be queried through the I²C bus. Level shifters on the I²C clock (SCL) and data (SDA) lines enable I²C communication with microcontrollers operating at the same voltage as VIN (2.6 V to 5.5 V). A detailed explanation of the I²C interface on the VL53L0X can be found in its datasheet (1MB pdf), and more detailed information about I²C in general can be found in NXP’s I²C-bus specification (1MB pdf).
The sensor’s 7-bit slave address defaults to 0101001b on power-up. It can be changed to any other value by writing one of the device configuration registers, but the new address only applies until the sensor is reset or powered off. ST provides an application note (196k pdf) that describes how to use multiple VL53L0X sensors on the same I²C bus by individually bringing each sensor out of reset and assigning it a unique address.
The I²C interface on the VL53L0X is compliant with the I²C fast mode (400 kHz) standard. In our tests of the board, we were able to communicate with the chip at clock frequencies up to 400 kHz; higher frequencies might work but were not tested.
In contrast with the information available for many other devices, ST has not publicly released a register map and descriptions or other documentation about configuring and controlling the VL53L0X. Instead, communication with the sensor is intended to be done through ST’s VL53L0X API (STSW-IMG005), a set of C functions that take care of the low-level interfacing. To use the VL53L0X, you can customize the API to run on a host platform of your choice using the information in the API documentation. Alternatively, it is possible to use the API source code as a guide for your own implementation.
We have written a basic Arduino library for the VL53L0X, which can be used as an alternative to ST’s official API for interfacing this sensor with an Arduino or Arduino-compatible controller. The library makes it simple to configure the VL53L0X and read the distance data through I²C. It also includes example sketches that show you how to use the library.
Size: | 0.5″ × 0.7″ × 0.085″1 |
---|---|
Weight: | 0.5 g1 |
Resolution: | 1 mm |
---|---|
Maximum range: | 2 m2 |
Interface: | I²C |
Minimum operating voltage: | 2.6 V |
Maximum operating voltage: | 5.5 V |
Supply current: | 10 mA3 |
PCB dev codes: | irs11a |
---|---|
Other markings: | 0J9776 |
The X-NUCLEO-53L0A1 expansion board features the VL53L0X ranging and gesture detection sensor, based on ST’s FlightSense™, Time-of-Flight technology. It is an evaluation board that provides an introduction to the ranging and gesture detection capabilities of the VL53L0X module
Integrated circuit - a distance sensor based on the technique of measuring the time between transmitting a light wave and returning its reflection (so-called Time of Flight - ToF). The system transmits data via the I2C bus and can measure distances up to 2 meters. The system has a small size and fits in the Optical LGA12 housing
No product available!
Mini module with ToF VL53L5CX sensor with a matrix of 64 pixels and a range of up to 4 m. It is equipped with a Qwiic connector and communicates via the I2C interface. SparkFun SEN-19013
Laser distance sensor with a measuring range of up to 4 m, based on the ToF measurement technique. Communication with the module takes place via the I2C interface. Waveshare VL53L1X Distance Sensor
URM04 v2.0 Ultrasonic Sensor
The GP2Y0A60SZ distance sensor from Sharp offers a wide detection range of 4″ to 60″ (10 cm to 150 cm) and a high update rate of 60 Hz. The distance is indicated by an analog voltage, so only a single analog input is required to interface with the module.
Ultrasonic distance sensor MB1010 with a range from 0 to 645 cm. It has an output in the form of a serial interface, analog signal or generates an impulse whose duration is proportional to the measured distance. Pololu 726
Optical distance sensor in the range of 20-150 cm with analogue output, power supply 4.5-5.5V.
Adjustable proximity sensor E18-D80NK allows detection of the object at a distance of 3 - 80 cm. Detection of an obstacle occurs due to the appearance of reflected infrared light.
Laser sensor module with a range of up to 50 m and an accuracy of 1 mm. Communication with the module takes place via the UART interface.
No product available!
Distance Sensor Breakout VL53L1X is a distance sensor with a range of 4m and a supply voltage of 2.6 ... 3.5V. Communication with the sensor takes place via the I2C interface. SEN-14722
Laser distance sensor with a measuring range from 0.1 m to 12 m. Optimized for industrial applications. Benewake TFmini-i
No product available!
Adafruit VL53L0X Time of Flight Distance Sensor is a laser distance sensor using the ToF (Time of Flight) measurement technique. The module is powered by 2.8 ... 5V voltage and can measure up to 1000mm. Adafruit 3317
360-degree laser scanner (LIDAR) with a range of up to 10 meters and a measurement frequency of up to 12 Hz. LIDAR X4
Laser scanner using ToF technology. It takes measurements at up to 10 revolutions per second and has a range of up to 25 m. Waveshare DTOF LIDAR STL27L
No product available!
Module with ToF VL53L4CD sensor with a range of up to 1.3 m and a resolution of 1 mm. It is equipped with a STEMMA QT connector and communicates via the I2C interface. Adafruit 5396
ToF distance sensor module based on the VL53L1X system. It offers a range from 4 to 400 cm and communicates via the I2C, UART or Modbus interface. TOF400F
A module with a distance sensor GP2Y0E03 operating in the infrared band. The sensor measures between 4-50cm.
This sensor is a carrier/breakout board for ST’s VL53L0X laser-ranging sensor, which measures the range to a target object up to 2 m away.