![LC filter for DC 0-50V 4A power supply](https://kamami.pl/67484-large_default/lc-filter-for-dc-0-50v-4a-power-supply.jpg)
![LC filter for DC 0-50V 4A power supply](https://kamami.pl/67484-large_default/lc-filter-for-dc-0-50v-4a-power-supply.jpg)
zł8.57 tax excl.
LC filter connected to the output of the DC power supply with a voltage from 0 to 50 V and a maximum current of 4 A. It reduces voltage ripple and interference caused by the power supply
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
LC filter connected to the output of the DC power supply. It is built on the basis of passive L (coils) and C (capacitors) elements. It can be used in low voltage DC power circuits from 0 to 50 V with a maximum current of 4 A. The filter reduces voltage ripple and reduces noise caused by the power supply. It is connected between the output of the power supply and the receiver and will be used, among others, in the case of powering audio amplifiers or industrial devices. The filters can be connected in series to increase the noise suppression effect or in parallel to increase the output current.
LC filter connected to the output of the DC power supply with a voltage from 0 to 50 V and a maximum current of 3 A. It reduces voltage ripple and interference caused by the power supply
LC filter connected to the output of the DC power supply with a voltage from 0 to 25 V and a maximum current of 3 A. It reduces voltage ripple and interference caused by the power supply
LC filter connected to the output of the DC power supply with a voltage from 0 to 50 V and a maximum current of 2 A. It reduces voltage ripple and interference caused by the power supply
Step-Down DC-DC converter module based on the D24V150F7 chip. Input voltage 9..40V, output voltage 7.5V (max 15A). Pololu 2883
No product available!
USB - UART converter based on the PL2303TA chip. Compatible with voltages of 3.3 V and 5 V, it has been equipped with a miniUSB connector. Waveshare PL2303 USB UART Board (mini) V2
No product available!
Module with a single-channel driver of DC motors VNH2SP30. It allows you to control a DC motor with a supply voltage of up to 16 V and a current consumption of up to 30 A. Mini Monster Moto Driver
No product available!
Module with 2 relays SRD-05VDC-SL-C with a load up to 10 A. The board is equipped with a Grove connector and is controlled by a digital signal. Seeed Studio 103020132
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 7.5 V. The board measures only 0.7″ × 0.7″, but it allows a typical continuous output current of up to 2.5 A. Typical efficiencies of 85% to 95% make this regulator well suited for powering moderate loads like sensors or small motors.
Module with electromechanical relay. It allows you to control devices with an operating voltage of up to 250 V AC and a current of up to 3 A or a voltage of 30 V DC and a current of 3 A
ACS714 Current Sensor Carrier -30 to +30A
The compact (0.4″ × 0.5″) D24V5F5 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 5 V while allowing for a maximum output current of 500 mA. Pololu 2843
Module containing TSH82 operational amplifier from STMicroelectronics. The system has two built-in amplifiers and each of them is available separately on the pins of the board as inverting amplifiers. Sparkfun BOB-14874
DC motor driver with an operating voltage from 6 to 60 V and a maximum continuous current of 300 A. It can communicate via USB, UART, RC or analog signal and allows for the implementation of a feedback loop. Pololu 3584
No product available!
The compact (0.4″ × 0.5″) D24V5F15 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 15 V while allowing for a maximum output current of 500 mA. Pololu 2847
TDA2030A mono digital audio amplifier module. The system allows you to connect one loudspeaker with an impedance from 4 to 8 Ω and a power of 18 W
Module with 4 SSR relays with a load of up to 3 A. The board communicates via the Ethernet interface. Numato Lab 4ETHSSR001-DC
No product available!
LC filter connected to the output of the DC power supply with a voltage from 0 to 50 V and a maximum current of 2 A. It reduces voltage ripple and interference caused by the power supply
Flex Cable for Raspberry Pi Camera - 300mm / 12"
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5048
No product available!
LC filter connected to the output of the DC power supply with a voltage from 0 to 50 V and a maximum current of 4 A. It reduces voltage ripple and interference caused by the power supply