zł86.72 tax excl.
HAT+ module intended for Raspberry Pi 5 enabling power supply via Ethernet in the PoE standard and connection of an M.2 NVMe drive via the PCI Express interface. Waveshare 31536
PoE M.2 HAT+ (C) is an expansion module of the HAT+ type intended for use with Raspberry Pi 5. It enables powering the minicomputer using an Ethernet cable in the Power over Ethernet (IEEE 802.3af/at) standard, eliminating the need for a separate power supply.
The module is equipped with an M.2 connector supporting NVMe SSD drives in 2230 and 2242 form factors, connected to Raspberry Pi 5 via a PCI Express x1 interface. This allows the use of fast mass storage, including the possibility of booting the operating system directly from the NVMe drive.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Raspberry Pi Expansion Board, DC Motor / Stepper Motor Driver
An audio module with a DAC converter and a stereo amplifier designed to work with the Raspberry Pi. Adafruit 3346
No product available!
Module with real time clock (RTC) PCF8523 dedicated for minicomputers Raspberry Pi. It communicates via the I2C interface. Adafruit 3386
Controller module for building an arcade game dedicated to Raspberry Pi. Connectors placed on the board allow you to connect 6 momentary buttons, a joystick and a loudspeaker. Adafruit 3422
RTC DS1307 module with clock dedicated to matrix displays with HUB75 interface. Designed for minicomputers Raspberry Pi. Adafruit 2345
No product available!
This RGB LED HAT can be easily attached on top of the Raspberry Pi to display colorful effect, and controlled by only one signal pin.
4 Port USB HUB HAT for Raspberry Pi B+, Raspberry Pi 2 B, Rapsberry Pi 3 B; USB to UART Onboard. Waveshare USB HUB HAT
Small GPS location module with L80-39 GPS chip, USB and TTL two ports,easy to be used with Raspberry Pi, Arduino, STM32 and other kind of micrcontrollers. The GPS module uses NMEA0183 communication protocol, integrated ultra-small SMA antenna connector. DFRobot TEL0119
No product available!
MATRIX Creator is an extension for the Raspberry Pi computer. It has Atmel ATSAM3S2C Cortex microcontroller and programmable FPGA. The board also has communication modules: Zigbee, Z-Wave or NFC. The peripherals are min. pressure sensor with altimeter, 35 RGBW diodes, 8 microphones and many more. MATRIX.C1.EU
No product available!
LCD display with a resolution of 800x480 pixels with a resistive touch panel. Designed for Raspberry Pi minicomputers. Waveshare 4inch HDMI LCD
Module with E-Ink display with a resolution of 250x122 pixels and a diagonal of 2.13 inches. Designed for the Raspberry Pi computer (HAT overlay). SPI interface communication. Waveshare 2.13inch e-Paper HAT
This add-on board makes it easy to control two high-power DC motors with a Raspberry Pi. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 36 Voperating range and are efficient enough to deliver a continuous 14 A without a heat sink. The drivers offer basic current limiting functionality, and they accept ultrasonic PWM frequencies for quieter operation.
HAT module with a driver for two DC motors designed for Raspberry Pi. Motors can be powered with the voltage from 6.5 to 30 V and draw a maximum current of up to 18 A. Pololu 3751
No product available!
This add-on board makes it easy to control two high-power DC motors with a Raspberry Pi. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 Voperating range and are efficient enough to deliver a continuous 18 A without a heat sink. The drivers offer basic current limiting functionality, and they accept ultrasonic PWM frequencies for quieter operation.
HAT+ module intended for Raspberry Pi 5 enabling power supply via Ethernet in the PoE standard and connection of an M.2 NVMe drive via the PCI Express interface. Waveshare 31536