

zł19.00 tax excl.
KAmodLSM303C is a module with the MEMS LSM303C chip from STMicroelectronics. The chip has a digital signal output (I2C or SPI bus) and allows measurement of accelerations and magnetic field values in three axes
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 12:00
Each consumer can return the purchased goods within 14 days
KAmodLSM303C is a module with the MEMS LSM303C chip from STMicroelectronics. The chip has a digital signal output (I2C or SPI bus) and allows measurement of accelerations and magnetic field values in three axes. Thanks to the programmable interrupt generator outputs, it is possible to wake up the microcontroller after detecting free fall or object movement. The board is equipped with a Pmod I2C standard connector and a KAMAMI connector, allowing easy attachment of the module to development kits. Due to its small dimensions, the product can be used in many development projects, while the Pmod through connector allows the boards to be connected in series.
Data sheet
Ultra-compact high-performance e-compass 3D accelerometer and 3D magnetometer module, LGA12, STM, RoHS
Four relay output module for Raspberry Pi 4B, Pi 3B+ Pi3B, Pi2, Pi+, Pi minicomputers.
KAmodPCF8883T is a module with capacitive touch sensor PCF8883 from NXP. The module has a probe placed on the PCB and a diode indicating the state of the chip. It enables work in one of three modes.
Voltage levels converter module with MAX3232 (RS232).
Shield for MAXimator set, 4-digit 7-segment LED display, 2 RGB type WS2812B diodes, STLM20 temperature sensor, two buttons
KAmodMPL3115A2 is a module with an atmospheric pressure sensor MPL3115A2 from NXP. Sensor allows to make a measurement in the range of 200...1100hPa (20...110kPa). Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMPL3115A2
Yellow 6-core connecting cable, 30 cm long. Intended for use with Kamami KAmod modules. It is terminated on both sides with a red plug that fits the WF06S connector. CAB_HU06-30-YELLOW
KAmodLSM6DS3 is a module that allows measurement of acceleration and angular velocity values. It has a built-in voltage stabilizer and level translators on SDA / SCL lines, thanks to which it can be used in 2.5-5.5V voltage systems
The KAmodPCAL6408 is an 8-bit I/O expander with the PCAL6408A chip by NXP, controlled by the I2C interface.
KAmodBT-HC05 is a Bluetooth module configured via AT commands. It has integrated LEDs indicating operating mode and connection status with the paired device, as well as a logic level translator on UART lines. KAmodBT-HC05
KAmodRPi-GPRS-GPS is an overlay for Raspberry Pi 4 / 3B + / 3B / 2B / B + computers, which allows you to enrich the system with the ability to send data via GPRS, SMS transmission or work as a module for Bluetooth communication. This extension also offers the ability to receive satellite data from location systems - GPS and GLONASS.
Module with TCS3200D system - sensor of RGB light components
KAmodMIC_MEMS is a module with a microphone type SPV1840LR5H-B. Thanks to the built-in amplifier with 100-fold signal amplification, the voltage at the module output can be measured using, for example, an ADC converter
No product available!
KAmodLSM303C is a module with the MEMS LSM303C chip from STMicroelectronics. The chip has a digital signal output (I2C or SPI bus) and allows measurement of accelerations and magnetic field values in three axes
We use cookies and other tracking technologies to improve your browsing experience on our website, analyze our website traffic, and to understand where our visitors are coming from. By browsing our website, you consent to our Privacy Policy.