KAmodPCF8883T – module with capacitive touch sensor
ID: 576065
5906623432721
zł19.90
Tax included
zł16.18 tax excl.
KAmodPCF8883T is a module with capacitive touch sensor PCF8883 from NXP. The module has a probe placed on the PCB and a diode indicating the state of the chip. It enables work in one of three modes.
Description
KAmodPCF8883T is a module with capacitive touch sensor PCF8883 from NXP. The board is equipped with a Pmod GPIO standard connector with one digital output informing about the status of the sensor output depending on the selected mode of operation and a KAMAMI connector, allowing easy connection of the module to development kits. The module has a probe placed on the PCB and a diode indicating the state of the chip. Due to its small dimensions, the product can be used in many development projects.
The module is equipped with jumpers enabling configuration of the system's operating mode. One of three jumpers may be on. Allows you to select the system operation in the mode:
- PB (Push Button) - the output is high as long as the probe event occurs
- PUL (Pulse) - the event is active for 1 second after the event occurs on the probe
- TOG (Toggle) - the occurrence of an event on the probe causes a change in the state on the output pin
Features
- NXP PCF8883T system
- Dynamic proximity sensor
- Wide input capacity range
- Automatic calibration
- Configurable operating mode (push-button, toggle, pulse)
- Wide operating temperature range: -40oC to +85oC
- Probe placed on the PCB
- Diode signaling the status of the OUT output
- Connector compatible with the Pmod GPIO standard
- Connector in accordance with the KAMAMI standard
- Built-in jumpers for selecting the system operation mode
- Can be supplied with voltage from 3 to 9 V
- Mounting holes with a diameter of 2.5 mm
- Dimensions: 51.3 mm x 20.3 mm x 10 mm
576065
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
A 30 cm long connecting cable (4 wires) designed for use with Kamami KAmod modules. It is terminated on both ends with a plug that fits the WF04S connector that KAmod modules are equipped with. cabhu04-30
zł6.90
24h
Available quantity: 3
Available
Capacitive 8-channel proximity switch with auto-calibration and very low power consumption, TSSOP28, NXP, RoHS
zł18.92
24h
Available quantity: 4
Available
Set of 40 pieces of male-female connection cables, in various colors, 17 cm long. CAB_M-F (Rainbow-40-17)
zł5.97
Delivery date unknown
No product available!
A set of 40 female-female connection cables, in various colors, 17 cm long. CAB_F-F (Rainbow-40-17)
zł5.69
Delivery date unknown
No product available!
Other products in the same category (16)
KAmodRPI RS485 CAN HAT is a shield for the Raspberry Pi computer that extends its interfaces with RS485 and CAN. Bus signals are led out to goldpin connectors and terminal blocks.
zł39.90
24h
Available quantity: 85
Available
ZL5USB is a USB-UART converter module based on Silabs CP2102. The module has small sizes, microUSB connector and it can works with the 2.5...5.5V signals.
zł24.90
24h
Available quantity: 318
Available
KAmodMC3635 is a module with the MC3635 three-axis accelerometer from mCube. The sensor allows the measurement of acceleration in the range of ±2g/±4g/±8g/±12g/±16g, the measurement frequency is from 14 to 1300 Hz. Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMC3635
zł14.90
24h
Available quantity: 453
Available
The KAmodPCAL6408 is an 8-bit I/O expander with the PCAL6408A chip by NXP, controlled by the I2C interface.
zł16.90
24h
Available quantity: 406
Available
A 30 cm long connecting cable (4 wires) designed for use with Kamami KAmod modules. It is terminated on both ends with a plug that fits the WF04S connector that KAmod modules are equipped with. cabhu04-30
zł6.90
24h
Available quantity: 3
Available
KAmodBT-HC05 is a Bluetooth module configured via AT commands. It has integrated LEDs indicating operating mode and connection status with the paired device, as well as a logic level translator on UART lines. KAmodBT-HC05
zł49.90
24h
Available quantity: 74
Available
Expander (overlay) extending the functionality of the STM32 Nucleo development board. Shield has ST Morpho connectors and is equipped with in a four-segment 7-segment display, four RGB diodes, LIS35DE accelerometer, LPS25HB pressure sensor, and DS18B20 digital thermometer
zł81.52
24h
Available quantity: 80
Available
KAmodM41T82 is a module with the STMicroelectronics M41T82 RTC clock. The chip allows precise timing, and an additional battery connector allows you to maintain the power supply when the main power is turned off. Communication with the module is realized via I2C bus.
zł31.49
24h
Available quantity: 457
Available
Module with DS18B20 temperature sensor from Dallas Semiconductor. The sensor used allows you to measure temperatures in the range -55 ~ 125 ° C with an accuracy of ± 0.5 ° C (in the range of -10 ~ 85 ° C). The 1-Wire interface is used for communication. The plate is equipped with a goldpin connector and a KAMAMI connector, allowing easy connection of the module to the commissioning kits.
zł13.90
24h
Available quantity: 368
Available
KAmodLIS35DE is a module with a three-axis LIS35DE accelerator from STMicroelectronics. The chip has a digital signal output (I2C or SPI bus) and allows acceleration measurement in three axes.
zł19.90
24h
Available quantity: 462
Available
KAmodRPi-GPRS-GPS is an overlay for Raspberry Pi 4 / 3B + / 3B / 2B / B + computers, which allows you to enrich the system with the ability to send data via GPRS, SMS transmission or work as a module for Bluetooth communication. This extension also offers the ability to receive satellite data from location systems - GPS and GLONASS.
Regular pricezł229.00zł206.10
24h
Available quantity: 47
Available
Multifunctional expander (shield) for NUCLEO and Arduino equipped with Bluetooth 2.0+EDR (HC-05) interface, MEMS 3DoF LIS35, LED-RGB, joystick and analog STLM20 temperature sensor developed and produced by KAMAMI.
zł99.00
24h
Available quantity: 36
Available
Available
KAmodLPS25HB is a module that allows the measurement of atmospheric pressure in the range of 260-1260hPa with a resolution of 0.01hPa, and thanks to the embedded regulator and voltage translator levels, it can be successfully used in systems supplied with a voltage of 2.5 - 5.5 V.
zł40.90
24h
Available quantity: 163
Available
Available
KAmodLSM303C is a module with the MEMS LSM303C chip from STMicroelectronics. The chip has a digital signal output (I2C or SPI bus) and allows measurement of accelerations and magnetic field values in three axes
zł37.90
24h
Available quantity: 406
Available
KAmodPCF8883T is a module with capacitive touch sensor PCF8883 from NXP. The module has a probe placed on the PCB and a diode indicating the state of the chip. It enables work in one of three modes.