New products
New products
Available
Available
zł73.05
Delivery date unknown
zł59.77
Delivery date unknown
Available
zł21.40
24h
Available
zł20.06
24h
Available
zł20.06
24h
Available
Available
Available
zł73.05
Delivery date unknown
zł59.77
Delivery date unknown
Available
zł21.40
24h
Available
zł20.06
24h
Available
zł20.06
24h
Available
Analog MEMS Microphone Breakout - module with an analog microphone SPH8878LR5H-1
ID: 1178841
5906623418220
zł31.72
Tax included
zł25.79 tax excl.
A module with a MEMS microphone and an amplifier that will allow you to detect a voice, a clap or a door slam. The board has an analog output. SparkFun BOB-19389
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
The module with the analog microphone MEMS SPH8878LR5H-1 and the operational amplifier, which allows the direct connection of the system to the ADC converter on the microcontroller. The microphone used is omni-directional, which means that it is good at picking up sound sources from all directions. The microphone port is located on the bottom of the board, so keep this in mind when installing the module in the project. The sensor will allow you to add sound to the application, it will allow you to detect voice, clap or slam the door. Full documentation with examples of use is available on the product page.
Features
- Supply voltage: 2.3 to 3.6 V
- Average current consumption: 265µA
- Frequency range: 7Hz to 36kHz
- Signal to noise ratio: 66dBV / Pa
- Sensitivity: ~ 44dBV / Pa (unidirectional mode)
- -3dB Roll Off at 7Hz / + 3dB at 36kHz
- Acoustic overload point: 134dB SPL
- OPA344 provides an output impedance of 600 Ω
1178841
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Pin header goldpin black 1x40 pins. Straight connector for through-hole assembly. 2.54mm pitch.
zł1.23 24hAvailable quantity: 5218 AvailableA set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł4.01 24hAvailable quantity: 411 AvailableA set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł4.19 24hAvailable quantity: 293 AvailableA set of 40 pcs of male-male connecting cables in various colors, 10 cm long
zł5.87 24hAvailable quantity: 25 Available
Other products in the same category (16)
Module with the WM8960 audio codec, which allows you to operate 1 W stereo speakers and two microphones via the I2S interface. Waveshare WM8960 Audio HAT
zł98.38 4 weeks No product available!
A module with an electret microphone, amplifier and ADC converter dedicated to micro: bit. It communicates via the I2C interface. SparkFun SEN-15289
zł40.61 24hAvailable quantity: 2 AvailableSound card in the form of an expansion module with a USB adapter designed for NVIDIA Jetson Nano development kits. Waveshare Audio Card for Jetson Nano
zł82.82 24hAvailable quantity: 3 AvailableMEMS SPM1423 digital microphone module with PDM modulation. It communicates via the I2S interface. M5Stack U089
zł22.90 24hAvailable quantity: 4 AvailableExpansion board compatible with STM32 Nucleo. Allows you to prototype solutions with digital microphones. STMicroelectronics X-NUCLEO-CCA02M2
zł139.09 24hAvailable quantity: 6 AvailableA volume sensor designed to detect loud ambient sounds. The module uses a microphone and LM2904 amplifier. The output value (analog signal) depends on the volume of the detected sound. In order to eliminate interference, the microphone signal is subjected to double filtering. Seeed studio 101020063
zł35.89 24hAvailable quantity: 1 AvailableAudio module with two microphones and display designed to work with the Raspberry Pi. Pimoroni PIM524
zł147.00 4 weeks No product available!
Audio Analyzer is a module with sound analyzer based on the MSGEQ7 system. It divides the sound into seven frequency bands, and then allows you to read the peak levels of each band. It allows you to measure the sound in the following frequencies: 63Hz, 160Hz, 400Hz, 1kHz, 2.5kHz, 6.25kHz and 16kHz. DFRobot DFR0126
zł90.48 24hAvailable quantity: 1 AvailableBOB-09868 - Breakout Board for ADMP401 MEMS Microphone, SparkFun
zł73.16 3 weeks No product available!
The VM-CLAP1 Hand Clap Sensor from Verbal Machines is a low-power, microprocessor-based audio sensor that can detect hand claps or finger snaps while ignoring background noises such as human speech or music. Pololu 2580
zł110.15 24hAvailable quantity: 1 AvailableA module with a MEMS microphone that will allow you to detect a voice, a clap or a door slam. The board has an analog output. DFRobot SEN0487
zł14.43 24hAvailable quantity: 4 AvailableA set with a vibration generator designed to transfer sounds through the human skeleton to the auditory center. DFRobot KIT0126
zł146.90 24hAvailable quantity: 1 AvailableModule with electret microphone and LM393 amplifier that will allow you to detect voice, clap, slam doors and other sounds using analog or digital output
zł4.19 24hAvailable quantity: 10 AvailableAudio module with Jack (TRS) connector and THAT 1206 balanced line receiver. Offers low distortion and high attenuation. SparkFun BOB-14002
zł78.02 24hAvailable quantity: 1 AvailableMEMS SPU0414HR5H-SB analog microphone module. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020852
zł41.97 24hAvailable quantity: 1 AvailableKAmodMIC_ELECTRET is a module with microphone KPCM6B type. Thanks to embedded amplifier with hundredfold amplification of signal, output voltage can be measurement in microcontroller with using e.g. ADC converter.
zł10.50 24hAvailable quantity: 168 Available
A module with a MEMS microphone and an amplifier that will allow you to detect a voice, a clap or a door slam. The board has an analog output. SparkFun BOB-19389