Quad DC Motor Driver Shield is a DC motor driver compatible with Arduino boards operating with 3.3V and 5V. The module allows direction and speed control (using PWM signals) of four independent DC motors, so it can be used eg in four-wheeled mobile robots. The controller can control motors supplied with voltage in the range of 2.5 ... 13.5 V and with a maximum current of 1.2 A (continuous load). The module was based on the popular TB6612FNG chip. The system has overheat protection and a circuit to detect too low voltage
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
Dual-channel electric motors controller (H-bridge) Arduino Motor Shield Rev3 with L298 for controlling two DC motors or one stepper motor with the possibility of using an electronic brake.
No product available!
(DRI0009) 2A Motor Shield For Arduino
This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 V operating range and are efficient enough to deliver a continuous 18 A without a heat sink.
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5038
No product available!
Motor-driven expansion board for Arduino, L293D, 74HC595 shift register, RoHS
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for self-assembly. Pololu 5037
No product available!
Shield with dual-channel DC motor driver for Arduino. It has an operating voltage from 7 to 30 V and a continuous current of up to 10 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron SHIELD-MDD10
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5041
No product available!
Pololu 2512Module with 2-channel DC motor driver for Arduino boards. It allows you to control drives with a supply voltage from 6 to 32 V and a current consumption of up to 0.65 A. Pololu 2512
Shield with dual-channel DC motor driver for Arduino. It has an operating voltage from 7 to 30 V and a continuous current of up to 1.2 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron SHIELD-3AMOTOR
Two-channel DC motor driver designed to work with Arduino boards. The module is based on the H L298 bridge system. It can control two DC motors up to 2 A per channel. SparkFun DEV-14129
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5036
No product available!
SimpleFOC Shield Type B enables precise control of BLDC motors using FOC technology, supporting supply voltages up to 35 V and working with Arduino and STM32. The module is equipped with INA240 current sensors and an IR2104 driver with configurable gate voltage, allowing precise motion control in robotics and automation projects.
This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its dual robust VNH5019 motor drivers operate from 5.5 to 24 V and can deliver a continuous 12 A (30 A peak) per motor, or a continuous 24 A (60 A peak) to a single motor connected to both channels. Pololu 2507
No product available!
Gravity: IO Expansion & Motor Driver Shield is an Arduino compatible expansion board that provides digital I / O ports, analog I2C, SPI and UART interfaces, as well as a DC motor driver. DFRobot DFR0502
No product available!
Pololu Dual MC33926 Motor Driver Shield for Arduino
Quad DC Motor Driver Shield is an Arduino compatible DC motor driver that allows you to control 4 DC motors with a voltage between 2.5 ... 13.5V and up to 1.2A. DFRobot DRI0039