

Extension module (shield) with a signal generator for Arduino Pro Mini. It can trigger a sine, square or triangle waveform up to 3MHz with an amplitude of 1Vp-p. It has two outputs and each has a Vcc/2 ground offset. The module can work with a voltage of 3.3 V (default) or 5 V after soldering the jumper and communicates via the SPI interface. The generator can also work as a standalone device. Full documentation is available on the product page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Microcontroller board based on the ATmega328P
Microcontroller board based on the ATmega328
Flexible GNSS antenna with u.FL connector attached with self-adhesive tape. Compatible with GPS, Galileo, BeiDou and GLONASS systems. SparkFun GPS-15246
No product available!
Adapter enabling easy and quick connection of Modulowo DuoNect to Arduino / Genuino expansion modules. MOD-75
The overlay solves the problem of limitations in the use of multiple overlays compatible with Arduino UNO R3. The board allows you to connect different shields without their mutual influence on each other (eg without conflict on the UART bus or GPIO lines). Extension dedicated for Arduino Mega and ADK devices. DFRobot DFR0256
No product available!
4inch Touch LCD Shield for Arduino is an overlay with a 4-inch LCD display. The screen has a resolution of 480x320 pixels. Communication with the display is via the SPI interface. Waveshare 4inch TFT Touch Shield
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
Multifunctional expander (shield) for NUCLEO and Arduino equipped with Bluetooth 2.0+EDR (HC-05) interface, MEMS 3DoF LIS35, LED-RGB, joystick and analog STLM20 temperature sensor developed and produced by KAMAMI.
The shield allows for easier connection of cables to the Arduino UNO R3 board. Thanks to the screw connectors, it is possible to fast and secure the cable, goldpin connectors allow you to easily connect the servo, and the built-in female connectors allow you to put additional Arduino shields
No product available!
Arduino Shield - MEGA Proto KIT Rev3
No product available!
The module with connectors is dedicated to the Arduino Portenta boards. It helps in prototyping and testing connections. Arduino ASX00031
Arduino Multifunctional Shield; LED, 7seg, buzzer, switch
Nano I / O Shield for Arduino Nano is an expansion board for Arduino Nano that provides digital, analog pins, power inputs and a connector for the Bluetooth module. DFRobot DFR0012
This shield allows you to interface Wixel wireless modules to your Arduino (and other compatible products), enabling simple wireless programming, debugging, and control using standard Arduino software. Pololu 2513
WiFiBee-MT7681 is an XBee module based on the MT7681 Wi-Fi module. WiFiBee supports standard IEEE802.11b / g / ni protocols. Can be used as a remote programmer for Arduino tiles. It is powered by 3.3 V. DFRobot TEL0107
(DFR0144) Relay Shield for Arduino V2.1
(DFR0105) Power Shield (Arduino Compatible)
LED matrix display module (in blue color) with an organization of 14 columns x 9 lines, compatible with Arduino.
Extension module (shield) with a signal generator for Arduino Pro Mini. It can trigger a sine, square or triangle waveform up to 3MHz. SparkFun BOB-11420