An essential companion to the Chibi Chip, the Chibi Clip Mounting Accessory enables rapid testing and re-use of the microcontroller board without any headache. With the Chibi Clip, attaching (and detaching) your Chip to circuits built on paper is as easy as using a clothespin.
The Chibi Clip was designed with classrooms and teachers on a tight budget in mind. Soldering and taping require consumables, and are semi-permanent attachment solutions that risk some damage to the Chip. The Clip uses the tension of its built-in spring to press the Chips’ electrodes onto copper tape, allowing quick and easy re-use of a Clip-mounted Chip between multiple projects and students.
When designing copper tape patterns to work with the Chibi Clip, it’s recommended to use the Chibi Chip as a guide and mark on the paper’s edge where the copper tape should go, before laying out the copper tape. Run the tape all the way to the edge of the paper, and make sure the tape is as smooth as you can make it before attempting to clip.
Note: The Chibi Clip Mounting Accessory does NOT include a Chibi Chip Microcontroller Board and will need to be purchased separately.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The Beetle shield is designed to attach a Beetle controller for easy connecting servos and sensors. DFR0285
Arducam Nano RPI Module is a minicomputer equipped with Broadcom BCM2835 processor and VideoCore IV GPU. The module has two CSI connectors for connecting cameras, video output (PAL), SPI, I2C, UART, and GPIO. ArduCam B0101
No product available!
Love To Code Chibi Chip is an educational module for learning programming designed for beginners of all ages and levels who want to start learning programming without installing software. DEV-14591, Adafruit 3674
Love to Code Chibi Clip Mounting Accessory
Love to Code Chibi Scope Display Accessory
Chibitronics Circuit Stickers Effects Add-On Pack
Espruino module with Bluetooth LE based on MDBT42Q system with Nordic Semiconductor nRF52832 microcontroller. The module has a pre-installed JavaScript interpreter. Adafruit 3876
Starter kit for IoT projects with micro:bit modules. It contains a micro: bit plate and 7 modules with sensors, executive elements useful in projects related to the Internet of Things. DFRobot KIT0138
Starter kit with Intel Quark D2000 microcontroller. It offers a 32-bit microcontroller, 6-axis IMU sensor, temperature sensor, USB-UART converter and CR2032 battery socket. The set has connectors compatible with Arduino. Intel Quark Microcontroller Dev Kit D2000
Evaluation kit with LittleBee GW1NR9 FPGA. It offers 8640 LUTs, 6480 Flip-Flops (FF), and has a built-in 8MB (64Mb) SDRAM. The board has 8 MB Flash, FTDI for UART, 8 LEDs and a button. TEC0117-01
No product available!
Single board computer with NXP i.MX 8M processor with 2 GB of DDR4 memory, Gigabit Ethernet port, two USB 3.0 ports, HDMI output, MIPI-DSI, MIPI-CSI, WiFi, Bluetooth Low Energy and MicroSD card slot. MaaXBoard AES-MC-SBC-IMX8M-G
No product available!
Development board with Bluetooth 5.2 BGM220P module from Silicon Labs. It is equipped with a mikroBUS socket and a Qwiic connector and a 20-pin connector with peripherals such as I2C, SPI, UART and GPIO. SparkFun DEV-17588
Evaluation platform with a DLP projector for a wide range of industrial applications such as 3D scanning, 3D printing and Automated Optical Inspection (AOI). EKB DPM-E4750RGBLC
No product available!
Evaluation platform with a DLP projector for a wide range of industrial applications such as 3D scanning, 3D printing and Automated Optical Inspection (AOI). EKB DPM-E4750RGBHBLC
No product available!
Evaluation platform with a DLP projector for a wide range of industrial applications such as 3D scanning, 3D printing and Automated Optical Inspection (AOI). Green light illumination. EKB DPM-E4750LCG-OX
No product available!
Single board computer with a quad-core ARM Cortex-A35 processor equipped with a 2.8-inch screen with a touch panel. It offers Wi-Fi and Bluetooth wireless communication. It is equipped with a light sensor, accelerometer, gyroscope and microphone. DFRobot DFR0706-EN
Love to Code Chibi Clip Mounting Accessory