The Chibi Scope is the perfect companion to your Chibi Chip Microcontroller Board. This display accessory for the Love to Code Chibitronics line is a small board equipped with an OLED screen that has been designed to help you understand what’s going on inside your Chibi Chip. It packs three essential functions — text, volts, and wave — into one compact package. The Chibi Scope connects to your Chibi Chip using the three included alligator clips; wire up +5V, GND, and TXT, and you’re ready to go.
Use the default “text” mode to help debug programs, display sensor values, and create text-based interactions. With the press of a button, the Chibi Scope goes into “volts” mode, showing the current input voltage on the screen. Press the button again, and the Chibi Scope goes into “wave” mode, displaying the shape of the voltage on its input pin over time, similar to an oscilloscope.
Since the Chibi Scope will display any serial text at 9600 baud (9600-N-8-1 for the technically inclined), it works with a wide range of other systems, including Arduino and Raspberry Pi development boards. So even if you already Love to Code, a Chibi Scope might still be a handy gadget to have around in your lab or office!
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Love To Code Chibi Chip is an educational module for learning programming designed for beginners of all ages and levels who want to start learning programming without installing software. DEV-14591, Adafruit 3674
Love to Code Chibi Clip Mounting Accessory
Chibitronics Circuit Stickers Effects Add-On Pack
The SparkFun Electric Imp imp002 Breakout allows you to explore the capabilities of the Imp product line in an easy to use package. The imp002 is actually a solder-down module version of the original Imp card. BOB-12958
Silicone case for the UNIHIKER computer. Provides a comfortable grip and good protection, reducing the likelihood of accidental drops and screen damage. DFRobot FIT0935
Starter kit for IoT projects with micro:bit modules. It contains a micro: bit plate and 7 modules with sensors, executive elements useful in projects related to the Internet of Things. DFRobot KIT0138
A specialized demonstration board designed to support Tail Tagging within the embOS/IP IP stack. Using this technology, it is possible to transform a single Ethernet port into several logical ports, enabling the creation of a virtual multiport network using only a single Ethernet port. Segger embOS/IP Switch Board (6.70.00)
No product available!
Arducam Nano RPI Module is a minicomputer equipped with Broadcom BCM2835 processor and VideoCore IV GPU. The module has two CSI connectors for connecting cameras, video output (PAL), SPI, I2C, UART, and GPIO. ArduCam B0101
No product available!
Evaluation platform with a DLP projector for a wide range of industrial applications such as 3D scanning, 3D printing and Automated Optical Inspection (AOI). EKB DPM-E4750RGBHBLC
No product available!
Base board for dipPLD modules with XC2C256 (CoolRunner-II by Xilinx)
Love to Code Chibi Clip Mounting Accessory
Evaluation kit with LittleBee GW1NR9 FPGA. It offers 8640 LUTs, 6480 Flip-Flops (FF), and has a built-in 8MB (64Mb) SDRAM. The board has 8 MB Flash, FTDI for UART, 8 LEDs and a button. TEC0117-01
No product available!
The Beetle shield is designed to attach a Beetle controller for easy connecting servos and sensors. DFR0285
Single board computer with NXP i.MX 8M processor with 2 GB of DDR4 memory, Gigabit Ethernet port, two USB 3.0 ports, HDMI output, MIPI-DSI, MIPI-CSI, WiFi, Bluetooth Low Energy and MicroSD card slot. MaaXBoard AES-MC-SBC-IMX8M-G
No product available!
Espruino module with Bluetooth LE based on MDBT42Q system with Nordic Semiconductor nRF52832 microcontroller. The module has a pre-installed JavaScript interpreter. Adafruit 3876
Compact development board with NXP LPC54605J512 microcontroller, ideal for prototyping and testing USB solutions, equipped with two USB-Host ports and support for SEGGER software such as emUSB-Host, emLoad and embOS. Thanks to the simple firmware update process and the built-in J-Link OB debugger, the board allows you to quickly and conveniently start working with USB devices in embedded projects. Segger emPower-USB-Host (6.90.00)
No product available!
Single board computer with a quad-core ARM Cortex-A35 processor equipped with a 2.8-inch screen with a touch panel. It offers Wi-Fi and Bluetooth wireless communication. It is equipped with a light sensor, accelerometer, gyroscope and microphone. DFRobot DFR0706-EN
Silicone case for the UNIHIKER computer. Provides a comfortable grip and good protection, reducing the likelihood of accidental drops and screen damage. DFRobot FIT0936
Love to Code Chibi Scope Display Accessory