zł105.56 tax excl.
Programmable laboratory power supply module utilizing STEP-DOWN converter technology and STM32 control for precise voltage and output current regulation. The construction supports DC 9–36 V input, 0.5–30 V / 0–5 A output, and I2C communication, enabling the creation of regulated power systems for electronics, automation, and embedded projects.
The M5Stack Module13.2 PPS programmable power supply module is designed for building adjustable power sources for electronics, embedded systems, industrial automation, and laboratory applications requiring precise voltage and current regulation. The construction utilizing a STEP-DOWN converter and STM32G030F6P6 microcontroller supports DC 9–36 V input voltage and adjustable 0.5–30 V / 0–5 A output with rated power of 100 W and peak power up to 150 W. The AD8418 current amplifier and closed-loop control system enable accurate output parameter readback with ±30 mV and ±5 mA accuracy, while factory full-range calibration increases operational stability during testing and powering electronic circuits.
The module features an I2C interface enabling power parameter control from M5Stack Core, Core2, and CoreS3 platforms. Integrated CA-IS3020S and B0505S-1WR3 isolation chips provide electrical isolation for communication and power buses, increasing operational safety for control systems. Standard 4 mm banana sockets with 19 mm spacing allow convenient connection of laboratory leads and test equipment. The module is suitable for building adjustable laboratory power supplies, automation projects, research experiments, embedded system development, and DIY projects requiring a programmable power source.
Note!
The module requires an external DC 9–36 V power supply — without a connected power source, the device will not be detected on the I2C bus and will not operate.
Manufacturer
Responsible person
Battery with a capacity of 190 mAh designed to power the M5ATOM series modules. M5Stack T001
Prototyping kit designed for sets from the M5ATOM series. It includes two boards with 60 prototyping fields and the necessary connectors. M5Stack A077
Prototyping kit designed for sets from the M5ATOM series. It includes a prototyping board and numerous connectors. M5Stack ATOM HUB DIY Proto
RS485 converter designed for sets from the M5ATOM series. It allows you to connect to development kits devices controlled by the RS485 bus. M5Stack T002
Dual-channel AC/DC programmable switch kit designed for M5Stack ATOM platforms, featuring relays rated for loads up to 250 V / 10 A (16 A instantaneous), an RS485 interface with Modbus support, and a built-in AC/DC power supply delivering 5 V / 1 A to the ATOM Lite module. The design supports remote control via WiFi or RS485, expansion through the HY2.0 Grove interface, and DIN rail mounting. The kit includes an ATOM Lite module based on the ESP32-PICO microcontroller together with a complete set of mounting accessories. M5Stack K042
ATOM Lite development kit complete with DRV8825 stepper motor driver module. M5Stack ATOM STEPMOTOR
ATOM Lite development kit complete with microSD card reader up to 16 GB. M5Stack K044
The universal DIY prototype module from the M5stack series with M-BUS connector. M5Stack M032
Lipo battery with a capacity of 750 mAh for the M5Stack sets. Modules can be connected in parallel and stacked. M5Stack M002
A 16-channel servo driver module designed to work with the M5Stack sets. It is powered with the voltage from 6 to 12 V. M5Stack M014-B
No product available!
Prototype kit for use in industry. It includes a prototype board with an M-BUS connector, TTL-RS485 converter, connectors and a DIN rail. M5Stack Base26
MEMS SPM1423 digital microphone module with PDM modulation. It communicates via the I2S interface. M5Stack U089
Module with gas sensor SGP30. It allows you to measure the content of total volatile organic compounds (TVOC), carbon dioxide equivalent (eCO2), ethanol and H2 in the air. M5Stack U088
Module with three Hall sensors A3144E, which react to the failure of the magnet. It is powered with 5 V and has a digital output on the Grove connector. M5Stack U084
Module with receiver designed for communication by means of a laser beam transmitted in the air. M5Stack Laser.Rx Unit
Module with a transmitter designed for communication via a laser beam transmitted in the air. M5Stack Laser.Tx Unit
Programmable laboratory power supply module utilizing STEP-DOWN converter technology and STM32 control for precise voltage and output current regulation. The construction supports DC 9–36 V input, 0.5–30 V / 0–5 A output, and I2C communication, enabling the creation of regulated power systems for electronics, automation, and embedded projects.