PmodTC1
ID: 557785
5906623491261
zł130.79
Tax included
zł106.33 tax excl.
K-Type Thermocouple Module
K-Type Thermocouple Module
The Digilent PmodTC1 is a temperature sensing peripheral module with cold-junction compensation and a K-Type thermocouple and is capable of measuring temperature ranging from -270° C to 1372° C. The temperature data is sent in an SPI read-only format as a signed 14-bit data stream with 0.25° C of resolution. Rather than being limited to measuring the ambient temperature, the TC1 with its K-Type thermocouple can safely collect specific point temperatures without damaging the IC.
Key Features
- SPI interface
- Temperature range of -270°C to 1372°C
- Cold-junction compensated
- Signed 14-bit, 0.25°C resolution
- ±2°C accuracy from -200°C to 700°C
- Comes with 30cm of K-Type thermocouple wire w/ 482° C-rated insulation
Download
Manufacturer: Digilent
Code: 410-315
557785
Data sheet
- Interface
- SPI
- Type of sensor
- MAX31855
- Sensor type
- Termopara
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Wireless, precise temperature sensor with high accuracy with built-in recorder. Works with thermoelectric sensors type K, J, T, N, E, B, S and R
Regular pricezł162.67zł99.02
24h
Available quantity: 1
Available
With the help of a thermocouple, it is possible to measure the temperature of the air and the surface. The use of a steel stainless steel tip in a K-type thermocouple allows the temperature to be measured up to 500 ° C. The cord length is approximately 100 centimeters. Adafruit 3245
zł52.21
24h
Available quantity: 7
Available
Other products in the same category (16)
The extension cable lets you locate your Pmod away from its host board, and the included male gender changer can provide extra connectivity to both system and prototyping boards. 240-021-1
zł26.57
3 weeks
No product available!
Maxim Dual Non-volatile Digital Pot - Peripheral Module
Regular pricezł159.92zł123.00
24h
Available quantity: 1
Available
No product available!
Pmod ESP32 is a module with the ESP-WROOM-32 system, allowing for WiFi communication, Bluetooth BLE 4.0 and Bluetooth. For communication, the SPI or UART interface is used (selected by means of the slide switch), which were output on the 12-pin Pmod connector. Digilent 410-377
zł201.38
24h
Available quantity: 3
Available
Evaluation Board with CN0336, 1xADC, 12-bit, Sampling Rate (Per Second) 300k, Analog Devices, RoHS
zł270.60
4 weeks
No product available!
Provides a 300 tie breadboard and 50 tie bus bar on an expansion card compatible with the NI myRIO Expansion Port (MXP). 210-283
zł133.81
3 weeks
No product available!
No product available!
Available
Evaluation board with AD7687, 1xADC, 16-bit, Sampling Rate (Per Second) 250k, Analog Devices, RoHS
zł184.20
24h
Available quantity: 1
Available
Available
Available
No product available!
Evaluation Board with CN0332, Magnetoresistive (MR) Rotational Speed Sensor, Analog Devices, RoHS
zł243.54
24h
Available quantity: 1
Available
Available
No product available!
The Pmod DHB1 uses DRV8833 dual H-Bridge motor driver chip to drive two DC motors or a single stepper motor. 410-259
zł106.04
3 weeks
No product available!
K-Type Thermocouple Module